The lap joint shown in Figure 4.2 is fastened by four 3/4 inch-diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivets is limited to 15.15 ksi and the bearing stress in the plates is limited to 19.15 ksi. Assume the applied load is uniformly distributed among the four rivets. 4 in 7/8 in 7/8 in Figure 4.2

The lap joint shown in Figure 4.2 is fastened by four 3/4 inch-diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivets is limited to 15.15 ksi and the bearing stress in the plates is limited to 19.15 ksi. Assume the applied load is uniformly distributed among the four rivets. 4 in 7/8 in 7/8 in Figure 4.2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If P=13000 N, d=22mm and t=33mm, determine the bearing stress between the rivets and plate, in MPa?
The lap joint shown is fastened by 6 − 20mm diameter rivets. Assuming that ? = 200??, determine (a) the shearing stress in each rivet, (b) the bearing stress in each plate 25mm thick and 100mm wide. Assume that the axial load ? is distributed equally among the 6 rivets, and the diameter of hole is 22mm.
The lap joint shown is fastened by five ¾ inch-diameter rivets. The bearing stress in the plates is limited to 15 ksi and the shearing stress in the rivets is 10 ksi. Assume the applied load is equally distributed among the five rivets. The thickness of each plate is ½ inch. Calculate the load P based on each stress given. Determine the maximum safe load P that can be applied. Express the loads in kips.
The lap joint shown in figure is fastened by four 1-in.-diameter rivets. (a) Calculate the minimum diameter of each rivet if the value of P is 30 kips and the bearing stress in the plates is limited to 4 ksi and the shearing stress in the rivets is limited to 15 ksi. Assume the applied load is uniformly distributed among the four rivets. Use 1 inch plate thickness.(b) Calculate the minimum thickness of plate if the value of P is 30 kips and the bearing stress in the plates is limited to 17.50 ksi. Assume the applied load is uniformly distributed among the four rivets.
Assume that the axial load P = 40kN applied to the lap joint is distributed equallyamong the three rivets. What is the smallest diameterof the rivetif the allowable stresses are 90 MPa for bearing between a plate and a rivet, and 40MPa for shear in rivets?
In the clevis shown, Solve for the: a) minimum bolt diameter and b) minimum thickness of each yoke that will support a load P = 18 kips without exceeding a shearing stress of 15 ksi and a bearing stress of 23 ksi.
For the assembly shown below, bar AB is loaded with P at its midspan. a.) If P = 10 kN, compute the shearing stress of a 10-mm-diameter pin at B in MPa. b.) If the bearing stress of a 6mm-thick plate at B is limited to 200 MPa and the shearing stress of 12mm-diameter pin is limited to 90 MPa, compute the maximum safe value of P in kiloNewtons. c.) If P = 15 kN and the bearing stress of the plate at B is limited to 120 MPa, calculate the required thickness of the plate (in mm). Diameter of the pin is 10 mm.
The lap joint shown is fastened by 6 − 20mm diameterrivets. Assuming that P = 200KN, determine (a) theshearing stress in each rivet, (b) the bearing stress ineach plate 25mm thick and 100mm wide. Assume that the axial load P is distributed equally among the 6rivets, and the diameter of hole is 22mm.
Six 20mm diameter rivets fasten the plate, as shown, to the fixed member. Determine the average shearing stress caused in each rivet by the P (in kilo-newton) loads. P=74 Show detailed solution
The steel pipe is supported on the base plate as shown in fig (5).if the t=50mm and d=300mm determine the bearing stress between the steel pipe and the based plate if the P=500 KN.
Problem 2: The lap joint shown is fastened by 6 − 20?? diameter rivets. Assuming that ? = 200??, determine (a) the shearing stress in each rivet, (b) the bearing stress in each plate 25?? thick and 100?? wide. Assume that the axial load ? is distributed equally among the 6rivets, and the diameter of hole is 22??. See figure 102. Show complete solution.
Two angle bars B and C are riveted to bracket A. Knowing that both angle bars are in compression and that force is 25 kN in angle bar B and 40 kN in angle bar C, determine thefollowing: a. Number of 19 mm diameter rivets in angle bar B if the allowable bearing stress of angle baris 60 MPa. Thickness of angle bar B is 6 mm.b. Number of 19 mm diameter rivets in angle bar C if the allowable shearing stress of rivets is25 MPa. Thickness of angle bar is 5 mm.