The length of the ship’s water-plane area is 70 m. The lengths of the equidistantly spaced half ordinates commencing from forward are as follows: 0, 5.2, 6.4, 7.0, 6.0, 4.9, 0.3. Find the area of the water-plane.

The length of the ship’s water-plane area is 70 m. The lengths of the equidistantly spaced half ordinates commencing from forward are as follows: 0, 5.2, 6.4, 7.0, 6.0, 4.9, 0.3. Find the area of the water-plane.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.108P: If the intensity of the line loading is w=[(40xx2)/40]lb/in., where x is measured in inches, use...

See similar textbooks

Related questions

Q: A diffuse surface at 1600 K has the spectral, hemispherical emissivity shown as follows. 1.…

A: Find

Q: Water enters a fountain through a pipe with a cross-sectional area A₁ at a flowrate Q. The pressure…

Q: Theory: (Optional) (Ref. Munson/Young/Okiishi A Brief Introduction to Fluid Mechanics, p.200-215)…

Q: du Water flows past a flat plate that has a length L = 5 m and a width w = 2 m, as shown in Figure…

A: Given Data: Water flows past a flat plate Plate Length L=5 m Plate Width w=2 m shear stress at the…

Q: Water enters a fountain through a pipe with a cross-sectional area ?1 at a flowrate ?. The pressure…

Q: Question #1: For the figure below, find the moment of the two forces about point (x,y,z) = (1,2,3)…

Q: 30° slope. Top block (30 kg) is attached by a wire and does not move. Middle block (50 kg) is…

Q: If the work done by a conservative force on a particle as it moves between two positions is equal to…

A: The work done by the conservative force,(W)=-10 lb-ft. Determine the change in potential energy.

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: Air pressure in the cylinder is increased by exerting forces P = 3 kN on the two pistons, each…

A: Force, P = 3 kN = 3000 N Radius, r = 45 mm = 0.045 m Wall Thickness, t = 2 mm = 0.002 m

Q: a particle travels along a straight line with a velocity of v=(4t−2t^2) m/s where t is in seconds…

A: v=(4t−2t2) m/s s =0 when t =0 To find: position of the particle, velocity and acceleration total…

Q: A hamster wheel of radius 25 cm has a rung that is travelling at a constant speed. The rung makes…

A: Radius of the wheel is 25 cm Time period is 3 sec. The wheel is 27 cm above the ground.

Q: 1. Determine the eccentricity and location (indicate your reference force) of the force on the…

A: Hi, We can solve only first question of for since the exact one is not specified. Please resubmit…

Q: A suspended object has a mass of 45 kg and is supported by the structure shown in the figure. You…

A: The mass of suspended weight is m=45 kg

Q: Q3: Plote the shear and moment diagrams for the cantilevered beam. 300 lb 6 ft 200 lb/ft

Q: In a thin plate, the state of stress prevails according to the figure. Calculate the principal…

Q: What do you know about the programme known as Pro/Engineer, which pertains to the field of…

A: INTRODUCTION: Mechanical engineering is the application of engineering ideas and problem-solving…

Q: (b) A steel strut of height 2 m, and cross-section 50 mm x 24 mm, is subject to an axial compressive…

A: It is asked o find

Q: Calculate the moment of inertia of the shaded area about the x-axis. A 78 mm 22 mm ----- 38 mm 38 mm…

A: A shaded area given composed of triangle and semi circle

Q: @1, W1 Z 1.5 m A W2, W₂ 12 m B At the instant 0 = 30°, the frame of the crane is rotating with an…

Q: The cross section of a bearing block is shown in the figure by the shaded area. Calculate the moment…

Q: Q3: A cylindrical shell of 1.3 m diameter is made up of 18 mm thick plates. Find the circumferential…

A: The circumferential and longitudinal stress. Given: The diameter of the cylindrical shell is d=1.3…

Q: s part of a processing of biofuels, water is pumped into a circular tank with a diameter ??, as…

A: For solution refer below images.

Q: 5. For a simple seismograph as shown in Figure Q5 below, the co-ordinate X₁ measures horizontal…

A: Here, The mass m=1 kg. The spring stiffness k=10 Nm-1. The coefficient of the damper, c=2Nsm-1.…

Q: Determine the x- and y-coordinates of the centroid of the shaded area. y 6" 1 T 8" -8" Answers:…

Q: A beam is loaded and supported as shown. (a) Use the double-integration method to determine the…

A: The values are w=18 kN/m, L=12.2 m, EI=50000 kNm2

Q: 1. A uniform crane arm (length L) is attached to the rest of the crane by a frictionless axle at its…

Q: Question #3: There is a linearly distributed load applied around a circle (below). The magnitude of…

A: Given-Information: Magnitude,λ=14lb/ftRadius, R=3ft To-Determine: 1. Moment at A, B. 2. Net force.…

Q: PROBLEM 1 Find the support reactions and joint force of the construction, shown on the figure, if:…

A: As K is hingedp=12KNq=9 KN/mL=2mTaking M=9 Nm = 9×10-3 KNm

Q: Left schematic: a) if the two lines shown below are the walls of the mold, show the flow profile of…

A: Given Data: To Find: Polymer flow profile in both cases.

Q: 3-For the given loading, determine the zero-force members in the truss structure. H B D E G I J K M…

Q: Air at 7 kPa, 420 °C, and 400 m/s enters an adiabatic nozzle. The velocity of the air outlet is 700…

Q: When calculating "I", why have you used 50^3 x 24 rather than 24^3 x 50?

A: You have asked, When calculating "I", why have you used 50^3 x 24 rather than 24^3 x 50?

Q: The angular displacement of the centrifuge is given by 0-4[t+40e0020-40] rad, where t is in seconds…

Q: Calculate the poles, decay rate, damped natural frequency, undamped natural fre- quency, and damping…

A: Given: Gs=-3s2+4s+4 To find: Poles, decay rate, damped natural frequency, undamped natural frequency…

Q: The unbalanced wheel, as shown in Figure Q6 below, has a mass of 30 kg acting through its mass…

A: Given Data: m=30 kgkG=0.15 mω=2 rad/se=0.1 m To Find:

Q: 14 SKETCH THE APPROPRIATE AUXILIARY VIEW. 20

A: According to the given data We need to draw The auxiliary View of the object

Q: Draw the shear and bending-moment diagrams for the beam and loading shown, and calculate the maximum…

Q: This question requires the use of the Thermodynamic Property Tables supplied as additional material.…

A: P1=20 Mpa T1=500oc P2=0.1 Mpa Cp=461.5 J/Kg k

Q: Determine the reactions to the structure and tension in the cable

Q: A shear force of V=2.7 kips acts on the thin-walled section. Using dimensions of a 3 in., b-4 in., h…

Q: Three hundred and eighty five gallons of water per minute is flowing through a 4.3-in radius…

A: Given:Water flow rate, Q=385 gal/min=385448.831ft3/s=0.857784 ft3/s 1 ft3/s=448.831…

Q: As part of a processing of biofuels, water is pumped into a circular tank with a diameter D as shown…

A: For the solution refer below images.

Q: 1. Determine the magnitude of the resultant of the parallel force system shown below. Locate the…

Q: The shaft is subjected to a uniform distributed torque of T = 17 kN-m/m. The shaft is made of…

Q: An assembly worker on a production line obtains an Allen key within reach, positions it 15 cm (6…

A: handwritten solution attached

Q: Example 2: Refrigerant R-134a enter the compressor of a has a refrigerantor a superheared vapor at…

A: Given:Refrigerant=R134aRefrigerant condition at compressor inlet, P1=0.14 MPa, T1=-10oCRefrigerant…

Q: 1. hose: flexible/tubing: 2. pipe: nominal/tubing: 3. I.d. too small: inefficient/ wall too thin: 4.…

A: Here, we have to complete the relationship among fluid conductors and connectors by choosing…

Q: A uniform prismatic rod of length / and mass m is placed in a vertical position with one end on a…

A: Given Data: IG=2mr25 To Find: (a) The angular velocity of the rod. (b) Determine the height h.

Q: A cantilever of 5 m length carries a uniformly distributed load of 4 kN/m over a length of 3 m from…

Concept explainers

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Simpson's first rule

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the elevation h (km) where the weight of an object is one-tenth its weight on the surface of the earth.
Given that P=120lb and Q=130lb, find the rectangular representation of P+Q.
It can be show that a plane area may he represented by a vector A=A, where A is the area and represents a unit vector normal to the piano: of the area. Show that the area vector of the parallelogram formed by the vectors a and b shown in the figure is A=ab.
Determine the volume of the concrete arch dam.
The equation of the catenary shown is y = 100 cosh (x/100) where x and y are measured in feet (the catenary is the shape of a cable suspended between two points). Locate the y-coordinate 0f the centroid of the catenary by numerical integration using x=25ft.
Using the method of composite areas, find the dimension h that maximizes the centroid coordinate y of the plane region shown.
The center of gravity of the plane wire figure is located at G. Determine the lengths a and b.
Determine the dimensions of constants A and B far which the following equation is dimensionally homogeneous: F=Akx2sinBxk where F is a force, x is a distance, and k represents stiffness (dimensions: [FL1]).
The properties of the unequal angle section are Ix=80.9in.4,Iy=38.8in.4, and Iu=21.3in.4. Determine Ixy.
The concrete dam shown in cross section holds back fresh water (=1000kg/m3). Determine the resultant force R of the water pressure acting on one meter length of the dam. Also, compute the coordinates of a point on the line of action of R.
The position coordinate x of a particle is determined by its velocity v and the elapsed time t as follows: (a) x=At2Bvt; and (b) x=AvteBt. Determine the dimensions of constants A and B in each case, assuming the expressions to be dimensionally correct.