• The length where the shear is zero (x) (f applicable) • The maximum shear load (Vman) – positive (+) value if upward, negative (-) value if downward • The maximum moment (Mmas) – indicate if CW or CCW, BEWARE: - 500 N-m CW = 500 N-m CCW Draw the shear and moment diagram in your solution sheets. Box your final answers and write your final answers on the spaces provided below. Don't forget to include the units. Unable to box your final answers, not writing your final answers on the spaces below, and/or not writing the units will void your solutions and answers.

• The length where the shear is zero (x) (f applicable) • The maximum shear load (Vman) – positive (+) value if upward, negative (-) value if downward • The maximum moment (Mmas) – indicate if CW or CCW, BEWARE: - 500 N-m CW = 500 N-m CCW Draw the shear and moment diagram in your solution sheets. Box your final answers and write your final answers on the spaces provided below. Don't forget to include the units. Unable to box your final answers, not writing your final answers on the spaces below, and/or not writing the units will void your solutions and answers.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.8.6P: A cantilever beam of length L = 2 m supports a load P = 8,0 kN (sec figure). The beam is made of...

See similar textbooks

Similar questions

Calculate the distance e from the centerline of the web of a C 310 × 45 channel section to the shear center E (see figure). Note: For put poses of analysis, consider the flanges to be rectangles with thickness îrequal to the average flange thickness given in Table F-3(b) in Appendix F.
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
Calculate the distance e from the cent crime of the web of a C 15 x 40 channel section to the shear center 5 (see figure). Note: For purposes of analysis, consider the flanges to be rectangles with thickness teequal to the average flange thickness given in Table F-3(a) in Appendix F.
-15 A composite beam is constructed froma wood beam (3 in. x 6 in.) and a steel plate (3 in, wide). The wood and the steel are securely fastened to act as a single beam. The beam is subjected to a positive bending moment M. = 75 kip-in. Calculate the required thickness of the steel plate based on the following limit states: Allowable compressive stress in the wood = 2 ksi Allowable tensile stress in the wood = 2 ksi Allowable tensile stress in the steel plate = 16 ksi Assume that Ew= 1,500 ksi and es= 30,000 ksi.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb (see figure). The center of gravity of each child is 8 ft from the fulcrum. The board is 19 ft long, 8 in. wide, and 1.5 in. thick. What is the maximum bending stress in the board?
A cantilever beam of length L = 2 m supports a load P = 8,0 kN (sec figure). The beam is made of wood with cross-sectional dimensions 120 mm x 200 mm. Calculate the shear stresses due to the load/"at points located 25 mm, 50 mm, 75 mm, and 100 mm from the top surface of the beam. From these results, plot a graph showing the distribution of shear stresses from top to bottom of the beam.
A gantry crane of weight W=100 Kg moves across a bridge with the length I=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles.
A circular solid cross-section cantilever is fixed at one end and bears a concentrated load P at the other. Over a 2m length, the diameter increases uniformly from 200 mm at the free end to 400 mm at the fixed end. At what distance from the free end will the bending stress in the cantilever be maximum? If the concentrated load P=30 KN, what is the maximum bending stress
A full circular cross-section shaft will be designed to provide power transmission at 220 (revolution/minute) revolution of a 12300 kW engine. Since the shaft length is 3 m, the material shear modulus is 80 GPa, and the shear yield stress is 190 MPaa) How many kN.m torque should the shaft carry?b) Write down the minimum safe shaft radius in metersc) How many rad is the shaft at the specified minimum radius. found?
Determine the maximum positive normal bending stress that occurs in member ABC of the engine crane given the following information: Engine weight = 1500 lb Member ABC height (vertical cross sectional dimension) = 7 in Member ABC width (horizontal cross sectional dimension) = 1 in Express your answer to the nearest whole psi value. In your work, draw the shear and moment diagram for member ABC. For the question above, determine the maximum shear stress in member ABC that occurs between points A and B. Express your answer using the nearest whole psi value.
What is the minimum steel shear area (Av in sq.mm.) of a beam 300mm wide if fc'=21MPa and fy=340? let the spacing of stirrups be equal to 220mm Pls hand written solution