The load in the circuit shown absorbs 50 kVA of complex power at power factar pf = 0.83 lagging when the load voltage is Vi. = 480/0 Vrms. 0.150 j025 ww SL pf Part C Find the pawer factor of the saurce. Enter your answer as pf, +1. where the pf is expressed so t significant figures and +1 is entered to indicate whether the pf is lesading (+1) or lagging (-1). > Vlew Avallable Hintis)

The load in the circuit shown absorbs 50 kVA of complex power at power factar pf = 0.83 lagging when the load voltage is Vi. = 480/0 Vrms. 0.150 j025 ww SL pf Part C Find the pawer factor of the saurce. Enter your answer as pf, +1. where the pf is expressed so t significant figures and +1 is entered to indicate whether the pf is lesading (+1) or lagging (-1). > Vlew Avallable Hintis)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.45P: Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at...

See similar textbooks

Similar questions

In the figure, the circuit is given as VRS =√3 . 60V and Zy = 6 + j8. Find the value of C to be connected in order to make the power drawn from the system in a phase 1, to make the load current 1, and to make cos(φ) 1.
A 480V single phase load has resistance of 70 ohms and inductive reactance of -j45 ohms. Find the real power, the apparent power, and the power factor consumed by the load.
Under balanced operating conditions, consider the 3-phase complex power delivered by the 3-phase source to the 3-phase load. Match the following expressions, those on the left to those on the right. 0) Real power, Py (ii) Reactive power, Qu (ii) Total apparent power Sy (iv) Complex power, Sy (a) (V3 VLL. IL)VA (b) (V3 Vu sng) var (e) (V3 VLL. IL cos ø) W (d) Py +Qy Note that VLL is the rms line-to-line voltage, IL is the ms line current, and o is the power-factor angle.
In the circuit in the figure, there is a load consisting of the series connection of the resistor R0 and the inductance L0 between the terminals a and b. The amplitude of the VS (t) voltage is √2 150 volts, phase angle = 0 degrees, period T = 200π microseconds.Since R = 300 ohms and C = 1 microfarad a)Find the values of R0 and L0 that enable the load to draw maximum average power from the circuit when the load phase angle is constant at 45 degrees? b)Calculate the average power on the load?
Solve all parts or will dislike For the following circuit, the source voltage phasor is: ?s = 250.7∠ -4.16 deg ? a) Calculate the equivalent workshop impedanceb) Deduce the value of the phasor ?c) Calculate the voltage at the workshop terminals using the ohm lawd) Calculate the voltage at the workshop terminals using the law of loopse) Determine the real and reactive powers of the workshop and its power factor solve all parts or will dislike
Type your question here A power plant has to meet the following load demand: Load A: 100 MW from 8 AM - 6 PM Load B: 150 MW from 6 AM - 10 AM Load C: 50 MW from 6 AM - 10 AM Load D: 20 MW from 10 AM - 6 AM Plot the daily load curve and determine (a) diversity factor (b) load factor (c) daily energy produced.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: Give the value of reactive power per phase seen at load 2.
Visible power of Z1 = |S1| = 16 kVA and at 0.8 back power factor; Visible power of Z2 = |S2| = 25 kVA and operates at unit power factor; Loads ZW = 5 + j26ohm/conductor is connected to the source by transmission line; VL = 3.8 kV Find the visible power of source,power factor and rms of source
1. a) Find the average power dissipated in the line shown.2. b) Find the capacitive reactance that when connected in parallelwith the load will make the load look purely resistive.3. c) What is the equivalent impedance of the load in (b)?4. d) Find the average power dissipated in the line when the capacitivereactance is connected across the load.5. e) Express the power loss in (d) as a percentage of the power lossfound in (a).
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What are the RMS line current at load 1 and 2 respectively?
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator2. “Reactive power in a system is dissipated generally as thermal energy?”A. TRUEB. FALSE3. Which of the following statements are correct for three phase circuit:A. Sum of all the three phase currents is zero in unbalanced networkB. Total power transfer to load is constant with timeC. Neutral conductor is same size in terms of material used as in single phase conductorsD. Net apparent power consumed is equal to real power
Convert the wye-connected load to its delta equivalent. What is the per phase impedance of the delta equivalent load? What is the total real and total reactive power consumed by the three-phase load regardless if wye or delta?