The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air at this pressure and 20°C flows with a velocity of 8 m/s over a 1.5 m * 6 m flat plate whose temperature is 140°C. Determine the rate of heat transfer from the plate if the air flows parallel to the (a) 6-m-long side and (b) the 1.5 m side.

The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air at this pressure and 20°C flows with a velocity of 8 m/s over a 1.5 m * 6 m flat plate whose temperature is 140°C. Determine the rate of heat transfer from the plate if the air flows parallel to the (a) 6-m-long side and (b) the 1.5 m side.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.38P

See similar textbooks

Related questions

Q: Q1: Consider a hot automotive engine, which can be approximated as 0.40m wide, and 0.8m long…

A: Given Data The speed of the car is: γ=80 km/h=22.22 m/s The length of the engine block is: L=0.8 m…

Q: Q3/ An average person generates heat at a rate of 84 W while resting. Assuming one-quarter of this…

Q: Air at 20°C, 1 atm flows with a velocity of 4.5 m/s over a flat plate having a sharp leading edge.…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: What fluid property is responsible for the development of the velocity boundary layer? What is the…

A: When a fluid flows over any stationary surfaces like flat plate, bed of a river or the wall of a…

Q: Required information -0.5 where x Air flowing over a 1-m-long flat plate at a velocity of 7 m/s has…

A: To obtain the velocity gradient of air on the plate, we must first calculate the shear stress acting…

Q: Q3: Air flows across a 20-cm-square plate with a velocity of 5 m/s. Free-stream conditions are 10 C…

A: In general, there are three modes by which heat gets transferred from one place to another. The…

Q: Air flowing over a 1-m-long flat plate at a velocity of 7 m/s has a friction coefficient given as…

A: Given:- x=0.6m To find:- Wall shear stress

Q: In the laminar flow of air (Pr = 0.7) over a heated plate. if ö and S denote, respectively, the…

Q: For laminar forced convection over a flat plate, if the free stream velocity increases by a factor…

Q: What does the friction coefficient represent in flow over a flat plate? How is it related to the…

A: Drag force is a force acting on a body (moving or stationary)which is present in a moving or…

Q: During a cold winter day, wind at 55 km/h is blowing parallel to a 4m high and 10m long wall of a…

Q: Q1: Air at 300 K and 50 kPa flows over a 2-m-square plate at a velocity of 70 m/s. The plate is…

Q: Hot methane exhaust gas at 1 atm is being cooled by flat plates. The gas at 150°C flows parallel…

Q: It has a density of 5900 kg/m3 and a specific heat of 590J/kg.°C with a diameter of 15 cm. A…

Q: 5. The local atmospheric pressure in Denver, Colorado (elevation 1610 m) is 83.4 kPa. Air at this…

Q: A 13 FT X 16 FT flat plate is suspended in a room and subjected to airflow parallel to its surfaces…

Q: Question No. 3: During a cold winter day, wind at 55 km/h is blowing parallel to a 4-m-high and…

A: Convection heat transfer is given as: Q=hAs(Ts-T∞) Where, h is convection heat transfer coefficient.…

Q: What is the difference in force needed to stabilize a flat plate being sprayed with a jet of water…

A: The force exerted by jet depends on the area of jet or nozzle, velocity of jet coming out through…

Q: EES Metal plates (k = 180 W/m-K, p= 2800 kg/m², |and c, = 880 J/kg-K) with a length of 1 m and a…

Q: Air at 250C and 1.0 bar is flowing over a flat plate with a velocity of 8 m/s. Determine: (i) The…

Q: Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220°C flow is…

Q: A long 8-cm-diameter steam pipe whose external surface temperature is 90°C passes through some open…

A: Given data diameter of the pipe D = 8 cm = 0.08m External surface temperature of the pipe Ts = 900C…

Q: Example 2: The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air…

Q: Explain and discuss the significance of (i) Rayleigh number and (ii) Nusselt number in natural…

Q: Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates as shown in Fig 3. The gas at…

Q: A 0.4-W cylindrical electronic component with diameter 0.3 cm and length 1.8 cm and mounted on a…

A: Given data Diameter of component = 0.3cm = 0.003m Length of the component = 1.8 cm = 0.018m Velocity…

Q: Calculate the heat transfer from a 60 cm x 60 cm plate on which air flows at 40 C and. The plate…

Q: Air with a pressure of 1 atm and a temperature of 285 K flows in a duct rectangular shape with a…

A: Given, Pressure, P=1atmTemperature, T=285KMass flow rate, m=0.1kg/sDuct size=75mm×150mmLength of…

Q: A1.8-m-diameter spherical tank of negligible thickness contains iced water at 0°C. Air at 25°C flows…

Q: 1) Engine oil at 80°C flows over a 6-m-long flat plate whose temperature is 30°C with a velocity of…

Q: Consider laminar flow over a flat plate. How does the local friction coefficient change with…

A: In the boundary layer flow of a fluid over any surface, the local friction coefficient represents a…

Q: average wind velocity. & A 1.8-m-diameter spherical tank of negligible thickness contains iced water…

Q: Water at 25°C and 1 atm is flowing over a long flat plate with a velocity of 8 m/s. Determine the…

A: Given data T=25°cV=8 m/sRecr=5×105

Q: 5. The local atmospheric pressure in Denver, Colorado (elevation 1610 m) is 83.4 kPa. Air at this…

A: Given:P=83.4 KPaT=25°Cv=9 m/sA=2.5*5 m2

Q: How does the viscosity affect the drag force?

A: Explaining the effect of viscosity on drag force

Q: Water at 43.3°C flows over a large square plate at a velocity of 21 cm/s. The plate is 1.9 m long…

A: Reynolds number is calculated for V=.21 m/s. Nusselt number are found and from here H is calculated.…

Q: What is lift? What causes it? Does wall shear contribute to the lift?

A: given: What is lift? What causes it? Does wall shear contribute to the lift?

Q: Q3/Air at 0.5 atm pressure and 27 C flows across a 34-cm-square plate at a velocity of 20 m/s. The…

Q: QUESTION 3 a) During a cold winter day, wind at 55 km/h is blowing parallel to a 4-m-high and…

A: Dear student, According to the guidelines I am allowed to answer only one…

Q: Q2/Engine oil at 80°C flows over a 6-m-long flat plate whose temperature is 30°C with a velocity of…

Q: Air flows over a l-meter-wide flat plate at a constant velocity of 20 m/s and ambient conditions of…

Q: A plate with a negligible thickness of 50 cm in width and 100 cm in length and from its upper…

Q: What is the difference between streamlined and bluff bodies? Is a tennis ball a streamlined or bluff…

A: If bodies subjected to fluid,flow can be classified as sreamlined or bluff body. a body is said to…

Q: A 10-cm-diameter, 30-cm-high cylindrical bottle contains cold water at 3°C. The bottle is placed in…

A: Given:- Diameter of bottle=10cm height=30cm temp of cold water =3°C temp of air=27°C temp of water…

Question

100%

The local atmospheric pressure in Denver, Colorado
(elevation 1610 m), is 83.4 kPa. Air at this pressure and
20°C flows with a velocity of 8 m/s over a 1.5 m * 6 m flat plate whose temperature is 140°C. Determine the rate of
heat transfer from the plate if the air flows parallel to the (a)
6-m-long side and (b) the 1.5 m side.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Trending now

This is a popular solution!

Step by step

Solved in 10 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air at this pressure and at 30°C flows with a velocity of 4.8 m/s over a 2.3-m × 8-m flat plate whose temperature is 120°C. Determine the rate of heat transfer from the plate if the air flows parallel to the 2.3-m-side. The properties of air at 0.823 atm and at the film temperature of (120 + 30)/2 = 75°C are k = 0.02971 W/m·°C, ν = 2.486 × 10-5 m2/s, and Pr = 0.7166.
Consider laminar flow over a flat plate. How does the local friction coefficient change with position?
The airflow at 1 atm has a free stream velocity and temperature of 5 cm/s and 25°C, respectively. Determine the heat flux on the plate surface and the convection heat transfer coefficient of the airflow.
A 1.2-in-outer-diameter pipe is to span across a river at a 140-ft-wide section while being completely immersed in water. The average flow velocity of the water is 10 ft/s, and its temperature is 70°F. Determine the drag force exerted on the pipe by the river.
Calculate the heat transfer from a 60 cm x 60 cm plate on which air flows at 40 C and. The plate temperature is 100 C while the air speed is 5 m/s.
Question No. 3: During a cold winter day, wind at 55 km/h is blowing parallel to a 4-m-high and 10-m-long wall of a house. If the air outside is at 5°C and the surface temperature of the wall is12°C, determine the rate of heat loss from that wall by convection. What would your answer be if the wind velocity was doubled
Example 2: The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air at this pressure is 20°C flows with a velocity of 8 m/s over a 1.5 m  6 m flat plate whose temperature is 140°C (Figure). Determine the rate of heat transfer from the plate if the air flows parallel to the (a) 6-m-long side and (b) the 1.5-m side.
Mercury at 25°C flows over a 3-m-long and 2-m-wide flat plate maintained at 75°C with a velocity of 0.01 m/s. Determine the rate of heat transfer from the entire plate.
Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220°C flows in parallel over the upper and lower surfaces of a 1.5-m-long flat plate at a velocity of 3 m/s. If the flat plate surface temperature is maintained at 80°C, determine (a) the local convection heat transfer coefficient at 1 m from the leading edge, (b) the average convection heat transfer coefficient over the entire plate, and (c) the total heat flux transfer to the plate.
Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220oC flows in parallel over the upper and lower surfaces of a 1.5-m-long flat plate at a velocity of 3m/s. if the flat plate surface temperature is maintained at 80oC, determine (a) the local convection heat transfer coefficient at 1 m from the leading edge, (b) the average convection heat transfer coefficient over the entire plate, and (c) the total heat flux transfer to the plate.
A 4-m x 4-m flat plate maintained at a constant temperature of 80°C is subjected to parallel flow of air at 1 atm, 20°C, and 10 m/s. The total drag force acting on the upper surface of the plate is measured to be 2.4 N. Using momentum heat transfer analogy, determine the average convection heat transfer coefficient, and the rate of heat transfer between the upper surface of the plate and the air
An average person generates heat at a rate of 84 W while resting. Assuming one-quarter of this heat is lost from the head and disregarding radiation, determine the average surface temperature of the head when it is not covered and is subjected to winds at 10°C and 25 km/h. The head can be approximated as a 30-cm-diameter sphere. Assume a surface temperature of 15°C for evaluation of ms. Is this a good assumption?