Air at 20°C, 1 atm flows with a velocity of 4.5 m/s over a flat plate having a sharp leading edge. The plate surface isisothermal at 60°C.(a)Find out the distance from leading edge at which the flow in the boundary layer changes from laminar to turbulent.(b)Using exact solution,determinethe following parameters at the location established at part (a):(i)Thickness of the hydrodynamic boundary layer(ii)Thickness of the thermalboundary layer(iii)Local convective heat transfer coefficient

Air at 20°C, 1 atm flows with a velocity of 4.5 m/s over a flat plate having a sharp leading edge. The plate surface isisothermal at 60°C.(a)Find out the distance from leading edge at which the flow in the boundary layer changes from laminar to turbulent.(b)Using exact solution,determinethe following parameters at the location established at part (a):(i)Thickness of the hydrodynamic boundary layer(ii)Thickness of the thermalboundary layer(iii)Local convective heat transfer coefficient

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.50P

See similar textbooks

Similar questions

Air at 1000C flows at an inlet velocity of 2 m/s between two parallel flat plates spaced 1 cm apart. Estimate the distance from the entrance to the point where the boundary layers meet.
Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the thickness of the hydrodynamic boundary layer at a distance 0.3 m from the leading edge of the surface.
Air at 30oC (density=1.165 kg/m3, kinematic viscosity = 16x10-5 m2/s) flows over a flat plate at a free stream velocity of 4.19 m/s. Determine the boundary layer thickness at distances of 0.2m, 0.5 m and 0.8 m. Also determine the skin friction coefficients, both local and average, at these locations.
During a winter day, wind at 70 km/h, 5°C, and 1 atm is blowing parallel to a 4-m-high and 15-m-long wall of a house. Approximating the wall surfaces as smooth, determine the friction drag acting on the wall. What would your answer be if the wind velocity has doubled? How realistic is it to treat the flow over side wall surfaces as flow over a flat plate?
Air at 250C and 1.0 bar is flowing over a flat plate with a velocity of 8 m/s. Determine: (i) The distance from the leading edge where the flow becomes turbulent (ii) The thickness of the boundary layer at that location.
Air at 20°C, 1 atm flows with a velocity of 4.5 m/s over a flat plate having a sharp leading edge. The plate surface isothermal at 60°C. (a), determine the following parameters at a distance of 1.89m. i)Mass entrainment in the boundary layer (ii)The skin friction coefficient
Consider laminar flow over a flat plate. How does the local friction coefficient change with position?
For the steady flat plate boundary layer flow, determine the wall shear stress assuming the following velocity profile. Where, δ is the boundary layer thickness and U is the outer flow velocity (constant).
At subsonic speeds, how do the lift coefficient CL and drag coefficientCD for a wing vary with angle of attack α?
What fluid property is responsible for the development of the velocity boundary layer? What is the effect of the velocity on the thickness of the boundary layer?
Air at 20°C, 1 atm flows with a velocity of 4.5 m/s over a flat plate having a sharp leading edge. The plate surface isothermal at 60°C. (a)Find out the distance from the leading edge at which the flow in the boundary layer changes from laminar to turbulent. (b)Using the exact solution, determine the following parameters at the location established at part (a): (i)Thickness of the hydrodynamic boundary layer (ii)Thickness of the thermal boundary layer
What are the physical and quantitative evidence of turbulence in fluid flow?