The long ranger is riding through a sandstorm. Does his mask (a bandanna that covers his nose) significantly decrease the amount of sand he breathes in? assume the bandanna is made of fibers, each 300 u in diameter. They are woven in a simple weave that blocks 75 % of the projected area; the remaining 25 % is open, with holes up to 75 μ in diameter. For the purpose of this problem, the bandanna may be considered equal to a single row of parallel fibers, each 300 u in diameter, with 75 % of the flow area blocked and 25 % open. The gas velocity approaching the cloth as he breaths is 1 m/s. a). Estimate both the collection efficiency for 10 u particles and the cut diameter for bandanna used as a filter

The long ranger is riding through a sandstorm. Does his mask (a bandanna that covers his nose) significantly decrease the amount of sand he breathes in? assume the bandanna is made of fibers, each 300 u in diameter. They are woven in a simple weave that blocks 75 % of the projected area; the remaining 25 % is open, with holes up to 75 μ in diameter. For the purpose of this problem, the bandanna may be considered equal to a single row of parallel fibers, each 300 u in diameter, with 75 % of the flow area blocked and 25 % open. The gas velocity approaching the cloth as he breaths is 1 m/s. a). Estimate both the collection efficiency for 10 u particles and the cut diameter for bandanna used as a filter

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Y= 82 kg show complete solutions and FBD
Notice: This is only for REVIEW PURPOSES, this is NOT GRADED. A 100 block is in equilibrium. What is the magnitude of the frictional force between this block and the surface? Given: Us = 0.3 2 lb Options: A. 0 lb B. 1 lb C. 2 lb D. 3 lb E. Othe answer
A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed exactly at the 50 meter mark. The slope of the measured line is 1 degree and 30 minutes. The tension on the tape is 10 kg, and the weight of the tape per unit length is 0.05 kg/m. Determine the exact correction (m) to be applied due to slope if sag is neglected. need answers and solutions asap, thank you!
In a container filled with each of the following materials, at a porosity of 40%, determine the upward gradient required to cause quick condition fiber beads with a specific gravity of 1.55. a. 6.21 b. 0.33 c. 0.255 d. 0.99
This is a resistance calculation problem for construction equipment. Given facts shown below, answer the four questions:Facts:A fully loaded wheeled scraper (empty weight = 30.0 tons; fully loaded weight = 80.0 tons) must travel up a 3.0% slope on a muddy haul road.The average tire penetration of the machine is estimated to be 4.0 inches.After dumping the loaded weight, the scraper returns downhill with an empty weight. Type all your work with a final answer to each question below. Q1) What is the total resistance force in lb. that the machine is going uphill? Q2) Determine the effective grade (%) for the total resistance of going uphill? Q3) What is the total resistance force in lb. that the machine is coming downhill? Q4) Determine the effective grade (%) for the total resistance of coming downhill?
A block of wood 0.6m x 0.6m x “h” meters in dimension was thrown into the water, if floatswith 0.18m. Projecting above the water surface. The same block was thrown into a container of a liquid having a sp.gr. Of 0.90 and it floats with 0.14m projecting above the liquid surface. A. Determine the value of “h”.B. Determine the sp.gr. of the block.C. Determine the weight of the block.
A member 1.5 m long has a cross section 75 mm by75 mm. The member becomes 0.7 mm longer and0.01 mm narrower after loading. Determine Poisson’sratio for the material.
A 1.22mdiameter sphere floats half submerged in salt water (γ = 10.05 kN/ ). What minimum weight of concrete (γ = 23.56 kN/ ) used as an anchor will submerge the sphere completely?
A certain unsharpened cylindrical pencil is 0.25 inches in diameter and 10 inches long. what is the surface area of the pencil? a. 1in^3 b. 10in^3 c. 0.5 in^3 d. 5 in^3
Examples of the different loading types: i. Uniformly loaded circular area ii. Uniformly loaded rectangular area
solve your own and do not copy others' solutions and answers. Find the adj length, adj bearings, and area.
A tensile force of 20 kN is applied to a specimen with a gage length of 50mm. It isthen noted that the distance between the gage marks became 50.122mm. a,) What isthe modulus of elasticity of the specimen if its diameter is 10mm? b.) What is the axialstress of the specimen? Solution must have Free Body Diagram/drawing.