The machine base shown has a mass of 75 kg and is fitted with skids at A and B. The coefficient of static friction between the skids and the floor is 0.30. If a force P with a magnitude of 500 N is applied at corner C, determine the range of values of 0 for which the base will not move. 0.6 m · •G 0.5 m A B -0.8 m- 0.4 m

The machine base shown has a mass of 75 kg and is fitted with skids at A and B. The coefficient of static friction between the skids and the floor is 0.30. If a force P with a magnitude of 500 N is applied at corner C, determine the range of values of 0 for which the base will not move. 0.6 m · •G 0.5 m A B -0.8 m- 0.4 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.63P: The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The...

See similar textbooks

Similar questions

The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The two uniform sheets of plywood, each of length L and weight W, are propped as shown. If the coefficient of static friction is 0.5 at all three contact surfaces, determine whether the sheets will remain at rest.
The panel of weight W with its center of gravity at G is placed between vertical guides and released. Determine the largest height h for which the panel will not slide down due to binding at corners A and B. The coefficient of static friction between the panel and the guides is 0.5.
The screw of the carjack has a pitch of 0.1 in. and a mean radius of 0.175 in. Note that the ends of the screw are threaded in opposite directions (right- and left-handed threads). The coefficient of static friction between the threads is 0.08. Calculate the torque C0 that must be applied to the screw in order to start the 1200-1b load moving (a) upward; and (b) downward.
The mass of the unbalanced disk is m, and its center of gravity is located at G. If the coefficient of static friction is 0.2 between the cylinder and the inclined surface, determine whether the cylinder can be at rest in the position shown. Note that the string AB is parallel to the incline.
The test specimen AB is placed in the grip of a tension-testing machine and secured with a wedge. The coefficient of static friction at both surfaces of the specimen is s. If the wedge angle is =18, determine the smallest s for which the grip is self-locking (no slipping takes place regardless of the magnitude of the force P). Neglect the weight of the wedge.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.