The magnetic field in a region has a magnitude of 0.40 T and points in the positive z direction, as shown in the figure below. Calculate the magnetic flux through (a) surface, abcd, (b) surface, bcef, and (c) surface, adef. [Hint: The calculation in part (b) can be simplified by careful reasoning, but be sure to justify any simplifications you make. 0.5 m 0.3 m a 0.4 m 0.6 m

The magnetic field in a region has a magnitude of 0.40 T and points in the positive z direction, as shown in the figure below. Calculate the magnetic flux through (a) surface, abcd, (b) surface, bcef, and (c) surface, adef. [Hint: The calculation in part (b) can be simplified by careful reasoning, but be sure to justify any simplifications you make. 0.5 m 0.3 m a 0.4 m 0.6 m

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter30: Magnetic Fields And Forces

Section: Chapter Questions

Problem 75PQ

See similar textbooks

Similar questions

If electric and magnetic field strengths vary sinusoidally in time at frequency 1.00 GHz, being zero at t=0, then E=E0sin2ft. (a) When are the field strengths next equal to zero? (b) 4Jhen do they reach their most negative value? (c) How much time is needed for them to complete one cycle?
Repeat the previous problem, but with the loop lying flat on the ground with its current circulating counterclockwise (when viewed from above) in a location where Earth’s field is north, but at an angle 45.0° below the horizontal and with a strength of 6.0105T.
The conducting rod shown in the accompanying figure moves along parallel metal rails that are 25-cm apart. The system is in a uniform magnetic field of strength 0.75 T, which is directed into the page. The resistances of the rod and the rails are negligible, but the section PQ has a resistance of 0.25 . (a) What is the emf (including its sense) induced in the rod when it is moving to tire right with a speed of 5.0 m/s? (b) What force is required to keep the rod moving at this speed? (c) What is the rate at which work is done by this force? (d) What is the power dissipated in the resistor?
How is the percentage change in the strength of the magnetic field across the face of the toroid related to the percentage change in the radial distance from the axis of the toroid?
A current loop with magnetic dipole moment is placed in a uniform magnetic field , with its moment making angle θ with the field. With the arbitrary choice of U = 0 for θ = 90°, prove that the potential energy of the dipole-field system is .
A circular loop of radius R carries a current I. At what distance along the axis of the loop is the magnetic field one- half its value at the center of the loop?
Determine the magnetic field on the central axis at the opening of a semi-infinite solenoid. (That is, take the opening to be at x = 0 and the other end to be at x= .)
The magnetic flux through the loop shown in the accompanying figure varies with time according to m=2.00e3tsin(120t) , where m is in milliwebers. What are the direction and magnitude of the current through the 5.00 resistor at (a) t= 0; (b) t=2.17102 s and (c)t=3.00 s?
Check Your Understanding The wire loop forms a full circle of radius R and current I. What is the magnitude of the magnetic field at the center?
A reasonably uniform magnetic field over a limited region of space can be produced with the Helmholtz coil, which consists of two parallel coils centered on the same axis. The coils are connected so that they carry the same current I. Each coil has N turns and radius R, which is also the distance between the coils, (a) Find tire magnetic field at any point on the z-axis shown in the accompanying figure, (b) Show that dB/dz and d2Bdz2 are both zero at z = 0. (These vanishing derivatives demonstrate that the magnetic field varies only slightly near z = 0.)
Write the function for the torque as a function of angle theta, on a 50-turn square loop of a wire of 15.0 cm on a side that carries 20.0 A of current in a 2.00 T magnetic field if the inital torque is zero at an angle of 0 radians. a) What would be the values of the torque at angles Pi/4, Pi/2, 3Pi/4, Pi, 5Pi/4, 3Pi/2, 7Pi/4, and 2Pi? b) Sketch your torque function vs angle in radians from 0 to 2Pi using your values you calculated in part a.
Consider the situation shown in the figure. An electric field of 277 V/m is confined to a circular area d = 10 cm in diameter and directed outward perpendicular to the plane of the figure. If the field is increasing at a rate of 16.9 V/m·s, what is the magnitude of the magnetic field at the point P, r = 13.2 cm from the center of the circle?