Fill in the blanks.(Manufacturing)Thanks in advance is the elastic recovery of the sheet metal after bending....O springbackO earingO edge bendingO tearingO V-bendingO drawing811 aCrater wear on a tool leads toIncrease in cutting temperatureAll of theseWeakening of toolFriction forcesCutting forcesbIn.., a simple punch and die that each have the included angle are used to bend the part............wrinklingedge bendingearingV-bendingtearingThe main purpose of a boring operation, as compared to drilling, is to .........................Enlarge the existing holeDrill a holeCorrect the holeFinish the surfaceFinish the drilled holed The process of removing metal by a cutter which is rotated in the same direction of travel of workpiece, is called..........Up millingEnd millingFace millingSide millingDown milling

Ans(a) The elastic recovery of the sheet metal after bending is called springback. Inductile…

The main purpose of a boring operation, as compared to drilling, is to Enlarge the existing hole Drill a hole Correct the hole Finish the surface Finish the drilled hole The process of removing metal by a cutter which is rotated in the same direction of travel of workpiece, is cal ... Up milling End milling Face milling Side milling Down milling

The main purpose of a boring operation, as compared to drilling, is to Enlarge the existing hole Drill a hole Correct the hole Finish the surface Finish the drilled hole The process of removing metal by a cutter which is rotated in the same direction of travel of workpiece, is cal ... Up milling End milling Face milling Side milling Down milling

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flat milling operation will be carried out with a horizontal milling machine, in a piece of 250 mm in length and 50 mm in width, using a felicoidal bur with a diameter of 75 mm, with 10 teeth. If the feed per tooth is 0.2mm, and the cutting speed is 0.75 m / s, how would you determine the speed of metal removal to remove 6 mm from the surface of this piece?
Please give the correct solution A cylinder of 25 mm diameter and 100 mm length is turned with a tool, for which the relation VT0.25 = 55 is applicable. The cutting velocity is 22 m/min. For a tool feed of 0.046 mm/rev, the number of tool regrinds required to produce 425 cylinders is?
a) It has been stated that it is generally undesirable to allow temperatures to riseexcessively in machining operations. Explain why?b) List out the cutting parameters which is influenced the rises of cuttingtemperature during turning process.c) Evaluate the relationship of these cutting parameters to the cutting temperaturewith graph.d) Propose the solution of how to reduce the temperature during the cuttingprocess.
Discuss the effects of cutting speed, feed rate, and depth of cut on the tool wear rate during a turning operation. How does each parameter influence the surface finish of the workpiece? Provide a detailed explanation based on the principles of metal cutting mechanics.
A drilling operation is to be performed with a 12.7 mm diameter twist drill in a steelwork part. The hole is a blind hole at a depth of 60 mm and the point angle is 118 ̊. The cutting speed is 25 m/min and the feed is 0.3 mm/rev. determine The cutting time to complete the drilling operation,
In a turning operation, the tool life varies with cutting speed, as shown in following table:Cutting speed, V, m/min Tool life, T, min25 3070 2 Estimate the tool life for this operation at a speed of 60 m/min.
Note: Read the question carefully and give me right solutions according to the question. In orthogonal cutting of steel tube of 150 mm diameter and 2 mm thick, the cutting force was 130 kg and feed force was 35 kg for chip thickness of 0.3mm. The orthogonal cut was taken at 60 meter per minute with a feed of 0.14 mm/rev. If the back rack angle of the cutting tool was - 8 o (minus 8 degree), then calculate the shear strain and strain energy per unit volume.
Assuming that the coefficient of friction is 0.25, calculate the maximum depth of cut forturning a hard aluminium alloy on a 15-kW lathe (with a mechanical efficieny of 80%) at awidth of cut of 6 mm, rake angle of 0˚, and a cutting speed of 90 m/min, shear strength of 150 MPa.
In orthogonal turning of a bar 100 mm diameter with a feed of 0.25 mm/rev., depth of cut = 4 mm, cutting velocity = 90 m/min. it is observed that the main cutting force is perpendicular to friction force acting at the chip tool interface and cutting force is 1500 N. find (i) rake angle (ii) normal force.
In a turning operation, the operator has established that a single pass on the cylindrical workpiece must be completed in 5.0 min. The piece is 400 mm long and 150 mm in diameter. Using a feed of 0.30 mm / rev and a depth of cut of 4.0 mm, what speed of cut should be used to meet this machining time?
For turning operation, using the table below, find an approximate value for the required speed of rotation of the chuck, in rpm, if the cutting speed for the material 5417 mm/s and the radius of the wp is 0.01 m. Show details of your answer. n | we| o
2 1.63 With a carbide tool, the temperature in a cutting operation is measured as 650K when the speed and the feed is 0.05mm/rev. W hat is the approximate temperature if the speed is doubled? W hat speed is required to lower the maximum cutting temperature to 480K?