The mass flow rate from a Bernoulli obstruction meter is given as: m =CA/2PAP/(RT, ) Find the percent uncertainty in the mass flow rate for the following data: 0.9 ± 0.0075, Pı= 30 psia ± 0.8 psia, T1 = 85 F ± 1 F, AP = 1.5 psi ± 0.0035 psi, A = 1.5 in² ± 0.001 in? C %3D 2

The mass flow rate from a Bernoulli obstruction meter is given as: m =CA/2PAP/(RT, ) Find the percent uncertainty in the mass flow rate for the following data: 0.9 ± 0.0075, Pı= 30 psia ± 0.8 psia, T1 = 85 F ± 1 F, AP = 1.5 psi ± 0.0035 psi, A = 1.5 in² ± 0.001 in? C %3D 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air flows through a duct at 2,700 cubic feet per minute (CFM). After several feet and a few vents, the air-flow decreases to 1,890 CFM. What is the percent drop that has occurred? (Simplify your answer completely.)
A Venturi tube is to be used to measure a flow rate of water in a 120mm pipe. The maximum flow rate is equal to 0.30 m3/s, maximum differential pressure measured to be 1.6 x 105 Pa and the density of water is 1000 kg/m3. Ignore any correction factor. Determine the diameter of constriction.
1) A smooth steel pipe of diameter 500 mm and length 850 m carry water at the rate of 0.05 m3/sec. Find the head lost due to friction. Take Kinematic Viscosity of water as 0.018 x 10 m2/sec 2)Determine the friction factor, “f” if Ethyl Alcohol at 25 C is flowing at 5.3 m/sec in a standard DN 40 Schedule 80 steel pipe 3)Determine the energy loss that will occur as 100 Liters / min of water flows from a small copper tube to a larger tube through a gradual enlargement having an included angle of 30 degrees. The small tube has a 25 mm OD x 1.5 wall thickness; the large tube has an 80 mm OD x 2.8 mm wall thickness.
1. Water flows at a rate of 65 Li/min in a steel pipe of 45 mm diameter, K = 0.045x10-3 m, μ = 0.001 K/m.s. Determine the type of flow, the friction coefficient, and the head loss due to friction per meter length of the pipe using: (a) Moody chart and (b) using smooth pipe formula. 2. Determine the size of galvanized steel pipe needed to carry water for a distance of 180 m at 85 Li/s with a head loss of 9.0 m. Take ε = 0.15 mm.
A Pitot tube is going to be used with an airflow at 32°C and 5 atm, and a velocity is 3 m/s: a) What is the dynamic pressure (in Pa)? b) What is the uncertainty of the velocity measurement if the dynamic pressure is measured with a manometer having an uncertainty of 3 Pa? c)What is the relative uncertainty (in %) of the absolute uncertainty calculated in part b) with respect to the velocity measured?
An oil having specific gravity of 0.926 and viscosity of 350 Saybolt seconds flow through a 3//-diameter pipe orifice placed in a 5^-diameter pipe. The differential gage registers a pressure drop of 21.5 psi. Determineflow Q. Ans. 1.93 CFS
A venturi meter with a throat diameter of 100 mm is fitted in a vertical pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards at a rate of 0.06 m-3 s'1. The venturi meter coefficient is 0.96. Two pressure gauges calibrated in kilo newtons per square metre are fitted at tapping points, one at the throat and the other in the inlet pipe 320 mm below the throat. The difference between the two gauge pressure readings is 28 kN/m-3. Working from Bernoulli's equation determine the difference in level in the two limbs of a mercury manometer if it is connected to the tapping points and the connecting pipes are filled with the same oil
Nitrogen gas under a pressure pn = 15 psig is used for pumping kerosene at 25°C (density = 816 kg/m3, viscosity = 1.81 cP) through an elevation increase of 6 m. If there is an effective length of 45 m of nominal 2-in. schedule No. 40 pipe (commercial steel) between the two tanks, what is the flow rate of kerosene? Neglect exit kinetic-energy effects.
The venturi nozzle in the airflow experiment measures a static pressure of 7 psf (lb/ft2 ) before the nozzle and a static pressure of 2 psf after the nozzle. If the Reynolds Number of the flow is 5.7E+04, gc = 32.17 lmm-ft/lbf -s2 , ρ = 0.075 lbm/f t3 Dpipe = 5 in, and Dventuri = 2.74 in, find the flow rate in the pipe. Present answer in cfm.
A fire hose has an inside diameter of 6.5 cm. Suppose such a hose carries a water flow of 40.5 L/s starting at a gauge pressure of 1.68 × 106 N/m2 . The hose discharges through a nozzle having an inside diameter of 3.4 cm. Take the viscosity of water to be 1.005 × 10-3 (N/m2)⋅s dh = 6.5 cmdn = 3.4 cmP = 1.68 × 106 N/m2Q = 40.5 L/s a. the Reynolds number, NR, for flow in the fire hose to show that the flow must be turbulent, with NR≥ 3000. b. Calculate the Reynolds number, NR, for flow in the fire hose and nozzle to show that the flow must be turbulent, with NR≥ 3000.
An orifice meter is used to measure the volume flow rate in a pipe. It takes 12 readings (in m3/s):0.0182, 0.0188, 0.0179, 0.0183, 0.0182, 0.0176, 0.0191, 0.0185, 0.0184, 0.0180, 0.0178, and 0.0186.The true volume flow rate is 0.017920 m3/s.(a) Estimate the bias error (also called the systematic error) of the instrument.(b) For each reading, estimate the accuracy error (inaccuracy).(c) For each reading, estimate the precision error.(d) Calculate the sum of all the inaccuracies and the sum of all the precision errors. Can you find somesignificance to these sums? Discuss.(e) Calculate the mean bias error of all the readings as a percentage.
A fan has a suction static pressure of 40mm of water vacuum with air velocity of 5m/s. The discharge has 160mm of water gage and discharge velocity of 9m/s. What is the total head of the fan if air density is 1.2kg/m3, mm of water gauge. Answer: 203.43