The mass of the belt is 0.6kg/m and the tension on the tight side of the belt is 1.7kN.the coefficient of friction between the belt and the pulley is 0.2 and the angular speed N, of the belt is 400rpm.Angle of lap fita and the diameter D of the pulley are 150° and 50cm respectively.with the addition of centrifugal tension, Design the belt drive by determine (A) velocity of the belt (B) centrifugal tension (C) tension on the slack side of the belt (D) power transmitted at this speed in kilowatts (E) maximum

The mass of the belt is 0.6kg/m and the tension on the tight side of the belt is 1.7kN.the coefficient of friction between the belt and the pulley is 0.2 and the angular speed N, of the belt is 400rpm.Angle of lap fita and the diameter D of the pulley are 150° and 50cm respectively.with the addition of centrifugal tension, Design the belt drive by determine (A) velocity of the belt (B) centrifugal tension (C) tension on the slack side of the belt (D) power transmitted at this speed in kilowatts (E) maximum

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.77P: The cone clutch transmits the torque C through a conical friction surface with cone angle . The...

See similar textbooks

Similar questions

The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
If there is no friction between shaft AB and the collar, what angular velocity Ö must the mechanism have to keep the collar at r= 660 mm from the vertical axis? Consider the same mechanism again, with m = 3.3 kg, d = 275 mm, k = 180 N/m, only now, instead of being smooth, the collar and shaft have a maximumcoefficient of friction of 0.74. What is the minimum angular velocity required to keep the collar at a constant distance r= 660 mm from the axis of rotation?
A centrifugal clutch has four shoes, each of mass 0·35 kg. When at rest, the radialclearance between the shoes and the clutch drum is 15 mm and the radius to the centre ofgravity of the shoes is 225 mm. The shoes are held on retaining springs of stiffness 10kN/m and the internal diameter of the clutch drum is 600 mm. The coefficient of frictionbetween the drum and the shoes is 0·3.Determine:(a) The speed (in rev/min) at which the clutch starts to engage. For a rotational speed of 1200 rev/min:(b) The force each shoe exerts on the drum. (c) The torque transmitted. (d) The power transmitted.
The tensions of a flat belt are;tight side 500N and slack side 180N.the angular speed N and diameter D of the pulley are 280rev/min and 20cm respectively.if the coefficient of friction between the belt and the pulley 0.6 and the mass m of the belt is 1.2kg/m, including centrifugal tension, Determine; (a) initial tension of the belt (b) angle of lap in degrees (C) power transmitted in the kilowatt (D) maximum power attainable in kilowatt
3. A vehicle, mass 1400 kg, passes a bend at a speed of 54 km/hr. The radius of curvature of the road is 60 m. Determine the minimum coefficient of static friction between the car tires and the road, so that the car can pass through corners safely.
The pistons of a 60° twin V-engine have strokes of 140 mm. The connecting rods driving a common crank has a length of 220 mm. The mass of the reciprocating parts per cylinder is 1 kg and the speed of the crank shaft is 2500 r.p.m. Determine the magnitude of the primary and secondary forces.
A centrifugal friction clutch has a driving member consisting of a spider carrying four shoes which are kept from contact with the clutch case by means of flat springs until increase of centrifugal force overcomes the resistance of the springs and the power is transmitted by friction between the shoes and the case. Power 22.5 kW is to be transmitted at 750 r.p.m. with engagement beginning at 75% of the running speed. The inside diameter of the drum is 300 mm and the radial distance of the centre of gravity of each shoe from the shaft axis is 125 mm. Assume μ = 0.25. Determine: 1. Mass of the shoes, and 2. Size of the shoes, if angle subtended by the shoes at the centre of the spider is 60o and the pressure exerted on the shoes is 0.1 N/mm2.
consider the mass and pulley system in the attached file. mass m1 = 29 kg and mass m2 = 12kg. the angle of the inclined plane is given and the coefficient of kinetic friction between mass m2 and the inclined plane is uk = 0.12. assume the pulleys are massless and frictionless when mass m2 moves a distance 4.94 m up the ramp, how far downward does mass m1 move? d= ?
A block of mass M1 resting on an inclined plane is connected by a string and pulleys to another block of mass M2 as shown in Fig. Find the tension in the string and acceleration of the blocks. Assume the coefficient of friction between the blocks M1 and the plane to be 0.2. M1=1500N , M2=1000N . Angle of inclined glane = 45 degrees
A 1500-kg automobile traveling along a straight, level road increasesits speed from 54 km/h to 90 km/h in a distance of 100 m. The efficiency of thedrive train is 85%, and the power output of the engine is constant. Determine theoutput horsepower of the engine during the acceleration. Neglect air and rollingresistance.
A pulley system uses a flat belt of cross sectional area 500 mm2 and density 1300 kg/m3. The angle of lap is 165O on the smaller wheel. The coefficient of friction is 0.35. The maximum force allowed in the belt is 600 N. If the the diameter of the smaller wheel is 50 cm and rotates at 3850 rpm , determine Initial tension in the belts and Power transmitted.
Consider the following arrangement of masses: Mass 1 is connected to mass 2 by a very light string and moves over a frictionless pulley so that both masses move with the same speed and move the same distances (?2 to the right a distance ? and ?1 down a distance ?).Assume ?1 = 15 ??, ?2 = 15 ??, and the coefficient of kinetic friction between ?2 and the table is ?? = 0.73. Let the masses start with an initial speed of 1.00 m/s. What is their speed after moving 1.00 cm (? = 0.0100 ?)?