The mass of the flat belt is 0.6kg/m and the tension on the tight side of the belt is 1.7kN the coefficient of friction between the belt and the pulley is 0.2 and the angular speed N of the belt is 400rpm.Angle of lap fita and the diameter D of the pulley 150°and 50cm respectively.with the addition of centrifugal tension Design the belt drive by determine velocity belt centrifugal tension tension on the slack side of the belt power transmitted at this speed in kilowatts maximum power delivered

The mass of the flat belt is 0.6kg/m and the tension on the tight side of the belt is 1.7kN the coefficient of friction between the belt and the pulley is 0.2 and the angular speed N of the belt is 400rpm.Angle of lap fita and the diameter D of the pulley 150°and 50cm respectively.with the addition of centrifugal tension Design the belt drive by determine velocity belt centrifugal tension tension on the slack side of the belt power transmitted at this speed in kilowatts maximum power delivered

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.81P: Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center...

See similar textbooks

Similar questions

The mass of the belt is 0.6kg/m and the tension on the tight side of the belt is 1.7kN.the coefficient of friction between the belt and the pulley is 0.2 and the angular speed N, of the belt is 400rpm.Angle of lap fita and the diameter D of the pulley are 150° and 50cm respectively.with the addition of centrifugal tension, Design the belt drive by determine (A) velocity of the belt (B) centrifugal tension (C) tension on the slack side of the belt (D) power transmitted at this speed in kilowatts (E) maximum
A centrifugal clutch has four shoes, each of mass 0·35 kg. When at rest, the radialclearance between the shoes and the clutch drum is 15 mm and the radius to the centre ofgravity of the shoes is 225 mm. The shoes are held on retaining springs of stiffness 10kN/m and the internal diameter of the clutch drum is 600 mm. The coefficient of frictionbetween the drum and the shoes is 0·3.Determine:(a) The speed (in rev/min) at which the clutch starts to engage. For a rotational speed of 1200 rev/min:(b) The force each shoe exerts on the drum. (c) The torque transmitted. (d) The power transmitted.
The figure shows a junction of mass m = 10kg sliding on a rod in a vertical plane. Positioned 1 simpai is stationary and horizontal spring and tensioned Fp = 300N. If the spring constant is k = 1kN/m and the average frictional force between the rod and the junction is F = 30N. Calculate the speed at position 2. (Ans: 3.47m/s)
Mason is is trying to keep a door open using a door stopper. That door is solid, and it has a mass of 18.3kg. The door closer is connected 26.2cm away from the hinge, and pulls with a force of 123N. The door stopper provides a static friction force of 13.2N, and a kinetic friction force off 11.8N. Find the angular acceleration (as a vector) of the door.
consider the mass and pulley system in the attached file. mass m1 = 29 kg and mass m2 = 12kg. the angle of the inclined plane is given and the coefficient of kinetic friction between mass m2 and the inclined plane is uk = 0.12. assume the pulleys are massless and frictionless what is the acceleration of mass m2 on the inclined plane? take positive acceleration to be up the ramp a2 = ?
A wheel tractor has a 200HP engine.If the weight of the wheel tractor is 30 tons and the weight on the drivingwheels is 50% of this weight, and it is operating at an altitute of 1000m above sea level, at an average temperature of 25 degree celcius, and at an average speed of 12km/hr. What is the maximum available rimpull if thecoefficient of traction is 0.25?. Take rimpull efficiency as 85%
the cylinder with a mass m1=2kg and radius r=0,1m is placed at a plate with mass m2=4kg. We are applying force F at this plate. Find an acceleration of the plate, when the friction coefficient μ=0,2
The G weight of the figure, when descending, rotates the axis fixed to drums, which are supported by two cylindrical bearings of known dimensions, with known angular velocity ω. Determine the value of weight G, neglecting the rigidity and friction in the rope and assuming that the velocity diagram in the lubricant is linear. Given Data: μ = 8x10⁻² N/m², Di = 0.100 m,D = 0.02 m, Li = 0.1 m,De = 0.101 m, ω = 20/π rd/s
If there is no friction between shaft AB and the collar, what angular velocity Ö must the mechanism have to keep the collar at r= 660 mm from the vertical axis? Consider the same mechanism again, with m = 3.3 kg, d = 275 mm, k = 180 N/m, only now, instead of being smooth, the collar and shaft have a maximumcoefficient of friction of 0.74. What is the minimum angular velocity required to keep the collar at a constant distance r= 660 mm from the axis of rotation?
A highway curve with a radius of 120 m is banked so thatthere is no lateral pressure on the wheels of a car at aspeed of 48 kph. A car weighing 17.8 kN with 1.5-mdistance between its wheels and height h = 0.70 m travelsaround the curve at 96 kph. (a) What is the normal forceon the car’s outer wheels? (b) If friction is great enough toprevent skidding, at what speed would overturningimpend?
An engineer is designinga conveyor system for loading haybales into a wagon (Fig.).Each bale is 0.25 m wide, 0.50 mhigh, and 0.80 m long (the dimensionperpendicular to the plane ofthe figure), with mass 30.0 kg. Thecenter of gravity of each bale is atits geometrical center. The coefficientof static friction between abale and the conveyor belt is 0.60, and the belt moves with constantspeed. (a) The angle b of the conveyor is slowly increased. At somecritical angle a bale will tip (if it doesn’t slip first), and at some differentcritical angle it will slip (if it doesn’t tip first). Find the twocritical angles and determine which happens at the smaller angle. (b)Would the outcome of part (a) be different if the coefficient of frictionwere 0.40?
The tensions of a flat belt are;tight side 500N and slack side 180N.the angular speed N and diameter D of the pulley are 280rev/min and 20cm respectively.if the coefficient of friction between the belt and the pulley 0.6 and the mass m of the belt is 1.2kg/m, including centrifugal tension, Determine; (a) initial tension of the belt (b) angle of lap in degrees (C) power transmitted in the kilowatt (D) maximum power attainable in kilowatt