The maximum dry density of a sample by the standard compaction test is 1.76 g/cc at an optimum moisture content of 14.5%. Find the air voids and the degree of saturation (G = 2.68). What would be the corresponding value of dry density on the zero air void line at optimum %3D moisture content?

The maximum dry density of a sample by the standard compaction test is 1.76 g/cc at an optimum moisture content of 14.5%. Find the air voids and the degree of saturation (G = 2.68). What would be the corresponding value of dry density on the zero air void line at optimum %3D moisture content?

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter5: Soil Compaction

Section: Chapter Questions

Problem 5.2P

See similar textbooks

Related questions

Q: Problem 1.7 The following results were obtained from a standard compaction test on a soil. The value…

A: Solution: Given Data: Gs=2.67Volume of mould=1000 cm3

Q: The soil with Gs = 2.7 and e = 0.8 has been air dried for 6 hours. After drying, the moisture…

A: Specific gravity of solids, Gs=2.7After oven drying, moisture content, w=20%=0.2Void ratio, e=0.7

Q: The minimum and maximum dry densities of a soil were determined in the laboratory to be 97.34 Ib/ft³…

A: Settlement is a process in which soil compaction with other soil particles is resolved by proper…

Q: What will be the dry density for a sample with the following properties, lying on the zero-air void…

A: G=2.67 w=42%

Q: Q6/ A field compaction control test was conducted on a compacted lift. The mass of the material…

A: Given data : Mass of removed material =1820 gm

Q: A laboratory modified Proctor compaction test gave: optimum water content 16 % and maximum dry…

A: Volume of the soil = 1165 cm3 Mass of the soil = 2230 gm Mass density, ρ = 22301165 = 1.91 g/cm3…

Q: The laboratory compaction test has a max. dry unit weight of 19kN/m³ with an optimum moisture…

Q: Following

Q: An undisturbed sample of sand has a dry weight of 4.20 lb and occupies a volume of 0.038 ft3. The…

A: The volume of voids in soil solids is calculated as,

Q: an undisturbed 1200 cm^3 sample of sand weighs 19.5 N when dry. The void ratios at the maximum and…

Q: A Standard Proctor compaction test performed on a sample of crushed limestone (G; = 2.70) obtained a…

Q: A standard proctor compaction test performed on a sample of soil having Gs= 2.70 obtained a maximum…

Q: The maximum and minimum dry unit weights of a sand were determined in the laboratory to be 16.9 kN/m…

Q: During a compaction test, a soil attains the maximum dry unit weight of 18.6 kN/m3 at a water…

Q: The maximum density of the sample by the standard compaction test is 1.76 g/cm3 at an optimum…

Q: The Table 4 shows the results of a Standard Proctor Compaction test. Based on the information…

A: "Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at…

Q: The following are the data of the compaction test: Volume of mold = 0.000945 m^3 Determine the…

A: Calculation of water content water content=wwws

Q: Q7: The Table 4 shows the results of a Standard Proctor Compaction test. Satisfactory Y N Based on…

Q: An undisturbed soil sample 30 mm thick got 50% consolidated in 20 minutes with drainage allowed at…

A: Given, Consolidation test result of laboratory, t1= 20min H1= 30mm For field:- H2= 4m Find:- time…

Q: A soil sample has a natural void ratio of 0.7. It was observed that void ratio of the soil sample in…

A: Given: Natural void ratio of soil, e = 0.7 Void ratio of soil in loosest state, emax = 0.85 Void…

Q: Q6/ A field compaction control test was conducted on a compacted lift. The mass of the material…

A: Given:-Mass of material removed from hole = 1820 gVolume of hole = 955cm3loss = 17gmass after drying…

Q: Results of a proctor compaction test are as follows; Trial 1: wet density = 126 Ib/ft., moisture…

A: we know that wet density = dry density(1+w) trial no wet density(lb/ft3) w% dry density 1 126…

Q: The max and min dry unit weights of sand were determined in the laboratory to be 16.5 kN/m3 and 14/6…

Q: The maximum density of the sample by the standard compaction test is 1.76 g/cm3 at an optimum…

Q: Determine the degree of saturation in percentage in a bulk density determination procedure on a…

Q: The compacted soil sample has 250 g mass and 1.89 g/cm³ density using 12% water content. If the…

Q: During a falling head test, the head fell from 80cm to 65cm in 83 seconds. The specimen was 5cm in…

Q: |A Standard Proctor test was performed on a clayey Sand soil: the test results are shown below.…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: The natural void ratio of a soil sample is 0.7. The void ratio of the soil sample was found to be…

Q: In a Proctor compaction test, the soil specimen of one of the observations had a bulk density of 19…

A: Given:Bulk density(γ=19 KN/m3Moisture contentw=15%w=0.15G=2.7We know that,In proctor compaction…

Q: The results of a Standard Proctoretest is tabulated as follows: (CHECK PICTURE) Determine the…

Q: A 1 m thick soil with an initial void ratio of 0.94 was compacted by a roller and its thickness…

A: Given Layer thickness = H = 1 me0 = 0.94 .... initial void ratio∆H = 0.09 m .... reduced change in…

Q: In a compaction test, as the compaction effort is increased, the optimum moisture content 9. A.…

A: Please refer the attached image for complete solution. THANK YOU.

Q: A sand cone test was conducted in the field. The mass of wet soil excavated from the hole is 3668.3g…

A: Mass of wet soil from hole (W1) =3668.3g Moisture of that soil (wc) = 17.2 % Weight of sand in hole…

Q: In proctor light compaction test, the bulk unit weight of soil sample was found to be 18 kN/m^3 at a…

Q: A sample of sand above the water table was found to have a natural moisture content of 10% and a…

Q: Sand cone equipment is used to determine an in-place unit weight (field density test) on a compacted…

Q: maximum density of the sample by the standard compaction test is 1.76 g/cm3 at an optimum moisture…

Q: - Soil Compaction 3. Results of the sand cone test are shown. A laboratory Proctor test determine…

Q: 5. A cubical sample of San Francisco Bay mud (a soft marine silty clay) has been prepared for…

Q: the modified compaction method for the same soil sample gives .moisture value than the standard…

A: The modified proctor test is also known as heavy compaction test. In the modified proctor test the…

Q: A modified Proctor compaction test was carried out using a cylindrical mold with a 1000 ml volume.…

A: Wet densityρ=Wet massVolumeDry densityρd=ρ1+wZero AIr voidZAV DensityρZAV=ρwGS1+wGSExample:at…

Q: Question 4 In a standard compaction test on a soil (grain specific gravity of 2.67) the following…

Q: An undisturbed sample of medium sand weighs 484.68g. The cylindrical core sample is 6 cm in diameter…

A: Bulk density: It is defined as the ratio of the weight of the sample to the total volume expressed…

Q: PROBLEM No. 4 Relative Density Maximum and minimum dry density tests were carried out on sand (G, =…

A: Given data:- Specific gravity of sand, G=2.67Volume of mould, V=1 literDensity in the loose state,…

Q: A soil profile is shown in Figure 11.19a. Laboratory consolidation tests were conducted on a…

A: Data given: e0 = 1 γsat = 18 kN/m3 σ0' = 40.95 MPa ∆σ = 48 MPa Asked: Settlement in the field…

Q: A cubical sample collected from Lobo shoreline (a soft marine silty clay) has been prepared for…

A: Solution Volume = 78 x 78 x78 = 474552 mm3V = 474.552 cm3moist Density (s) = 1.43…

Q: the maximum and minimum dry unit weights of a sand were determined in the laboratory to be…

Concept explainers

Soil Compaction Test

Soil compaction is the major area of geotechnical engineering. Soil is composed of multiple pores present on its surface, while the soil is mainly composed of gravel, sand, rocks, etc. The arrangement of these rocks and gravels is such that they build up voids (spaces) between them, which allows spaces for the roots of the plants and crops to spread and absorb the required amount of nutrients. Soil compaction is a major problem primarily caused by human activities, micro-organisms, and other multiple factors.

Question

The maximum dry density of a sample by the standard compaction test is
1.76 g/cc at an optimum moisture content of 14.5%. Find the air voids and the degree of saturation
(G = 2.68).
What would be the corresponding value of dry density on the zero air void line at optimum
moisture content?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The maximum density of the sample by the standard compaction test is 1.76 g/cm3 at an optimum moisture content of 14.5% (G=2.68). What would be the corresponding value of the dry density on the zero air voids line at optimum water content.
The maximum density of the sample by the standard compaction test is 1.76 g/cm3 at an optimum moisture content of 14.5% Find the air voids (G=2.68). a.8.8% b.7.7% c.10.10% d.9.9%
9. The results of a Standard Proctoretest is tabulated as follows: (CHECK PICTURE) Determine the maximum dry unit weight of compaction Determine the void ratio at the optimum moisture content Gs = 2.68 Determine the optimum moisture content Determine the degree of saturation at the optimum moisture content
The following are the data of the compaction test: Volume of mold = 0.000945 m^3 Determine the degree of saturation at the optimum moisture content if Gs= 2.60
3. The following table lists the results of a standard Proctor assay. Determine the maximum dry compaction density and the optimum moisture content. Also obtain the void ratio and degree of saturation for optimum moisture content. Assume Gs = 2.68.
The Table 4 shows the results of a Standard Proctor Compaction test. Based on the information provided, determine the following values. The maximum dry unit weight and the OMC.The degree of saturation at the maximum dry density if Gs = 2.70.What is the dry unit weight and the moisture range at 95% relative compaction (RC)?The degree of saturation at the maximum dry density if Gs = 2.70. Table 4: Results of a standard Proctor compaction test Trial No. 1 2 3 4 5 6 Moisture content, w (%) 6.2 8.1 9.8 11.5 12.3 13.2 Bulk unit weight (kN/m3) 16.9 18.7 19.5 20.5 20.4 20.1 Dry unit weight (kN/m3) 15.9 17.3 17.8 18.4 18.2 17.8
A Standard Proctor compaction test performed on a sample of crushed limestone (G; = 9.70) obtained a maximum dry unit weight of 80 pef at OMC. A field compacted sample showed a moisture of 98% and a unit weight of 803.7 pef. Find the relative compaction (RC). Find the degree of saturation S of the field soil sample.
The maximum density of the sample by the standard compaction test is 1.76 g/cm3 at an optimum moisture content of 14.5% Find the degree of saturation (G=2.68).
Q1. Undisturbed soil sample was collected from the filed in Melbourne in steel tube for laboratory evaluation. The tube has the diameter of 85 mm, length of 170 mm and the moisture weight of 1600 g. If the oven-dried weight was 1200 g and Gs = 2.69, calculate the followings:a) Bulk unit weight (?) in kN/m3b) Field moisture content (w)c) Void ratio & porosity (e and ⴄ) d) Degree of saturation (Sr)
A modified Proctor compaction test was carried out using a cylindrical moldwith a 1000 ml volume. Table 2 summarizes the results.a. Plot the compaction and ZAV curves (RD=2.75 and ρwater=1000 kg/m3).b. Determine the maximum dry density and the optimum moisture content.
The volume of the solids is 65cc. The wet weight of the soil is 198g having a saturation at 48% and the dried weight is 176g. Determine the following: a. Total volume of the sample, cc. b. Volume of the voids, cc. c. Air void ratio, %.
The results of a standard Proctor test are given in the following table. Determine the maximum dry unit weight of compaction and the optimum moisture content. Also determine the moisture content required to achieve 90% of ꙋd (max).