9. The results of a Standard Proctoretest is tabulated as follows: (CHECK PICTURE)Determine the maximum dry unit weight of compactionDetermine the void ratio at the optimum moisture content Gs = 2.68 Determine the optimum moisture content Determine the degree of saturation at the optimum moisture content 6.Problem:The results of a Standard Proctor Test istabulated as follows:Vol. of ProctorMold (cu.ft)Wt. of wet soilMoisturein mold (Ib)(%)121/303.691/303.82141/303.88161/303.87181/303.81201/303.7721 PROBLEMS for EXERCISESCOMPACTION CURVEMalare Waty Contna $a) Determine the max. dry unit weight ofcompaction.b) Determine the void ratio at the optimummoisture content if Gs = 2.68.c) Determine the optimum moisture content.d) Determine the degree of saturation at the.optimum moisture content.%3D10Problem:

Answered: Image /qna-images/answer/89e9890a-5918-4690-96f9-13b74ec1abed.jpg

The results of a Standard Proctoretest is tabulated as follows: (CHECK PICTURE) Determine the maximum dry unit weight of compaction Determine the void ratio at the optimum moisture content Gs = 2.68 Determine the optimum moisture content Determine the degree of saturation at the optimum moisture content

The results of a Standard Proctoretest is tabulated as follows: (CHECK PICTURE) Determine the maximum dry unit weight of compaction Determine the void ratio at the optimum moisture content Gs = 2.68 Determine the optimum moisture content Determine the degree of saturation at the optimum moisture content

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given: 1. Structural Component: Beam 300 mm x 400 mm Column 400 mm x 400 mm Slab thickness 110 mm 2. Dead Load: Super Imposed dead load = 4.5 KPa (including slab weight) CHB = 3.11 KPa 3. Seismic Parameter: Soil Profile - Sb Closest distance to the source - 10 km Ductility Coefficient R = 8.0 Seismic Zone Z=0.40 Ct = 0.0731 A. Compute the DESIGN BASE SHEAR (V = Cv*I*W /R*T). B. Compute the Minimum DESIGN BASE SHEAR (V =0.11Ca*I*W).
Answer no.2 question but plss adjust Correction in soil c in prob1 its 35% clay
Fill out the table and determine the ELEVATION of BM2. Show your solution. IGNORE "REMARK" COLUMN. THAT WAS SUPPOSED TO BE WHERE YOU PUT YOUR COMMENTS ON THE CONDITION IN THE FIELDWORK.
SHOW COMPLETE SOLUTION PLS VALUES:Y = 25
A course sand sample is placed in the constant permeameter test. Water passes through the sample water with a constant head of 40cm and after 0.00167hr, 40grams of water have been collected. What is the coefficient of permeability of the sand in cm/sec if the sample is placed inside a 166cm container with a 7.89cm radius?
Calculate % Silt using the following values; a. Weight of soil= 50 g b. HR reading at 40 sec.= 25 c. Temp at 40 sec= 25 oCd. HR at 2 hrs= 16 e. Temp at 2 hrs= 26 * A. 17.28 B. 17.25 C 17.22 D. 17.19
Define the term Degree of saturation.
Calculate % Sand using the following values; a. Weight of soil= 50 gb. HR reading at 40 sec.= 25c. Temp at 40 sec= 25 oCd. HR at 2 hrs= 16e. Temp at 2 hrs= 26 oC
Geotechnical Engineering (UPVOTE WILL BE GIVEN. PLEASE ANSWER THE QUESTION CORRECLTY. NO LONG EXPLANATION NEEDED. FOLLOW THE INSTRUCTIONS CAREFULLY.) A moist soil weighed 895 g with a volume of 425 cm3. After drying, the sample weighed 775 g. Of the dried soil, 400 g was poured into a vessel loose state. Its volume subsequently determined to be 275 cm3. That same 400 g was then vibrated and tamped to a volume of 212 cm3 with Gs = 2.71. Determine the designation of the granular soil based on its relative density. (3 decimal places - Do not round off unless it's the final answer)
Q. Triaxial test.
SUBJECT: SOIL MECHANICS A. Determine the approximate size of the soil CHOICES: a. 0.079mm b. 0.093mm c. 0.140mm d. 0.115mm B. Determine the approximate coefficient of Curvature CHOICES: a. 0.69 b. 0.84 c. 0.51 d. 1.03 C. Classify the soil using AASHTO classification system (with explanation) CHOICES: a. A-1-a b. A-3 c. A-1-b d. A-2-4
Subject: Soil Mechanics A. Classify the Soil Using USCS (with explanation/ justification) Given data: D10 = ? D30= 0.0023mm D60= 0.032mm Liquid Limit= 49% Plastic Limit= 24% CHOICES: a. CL (lean clay with gravel) b. CL ( lean clay with sand) c. ML (silt with gravel) d. ML (Silt with sand)