The maximum tensile stress o, from bending of a simply supported beam with length L and circular cross section with diameter D, is given by the expression 8FL , where F is the magnitude of a concentrated force acting in the middle of the beam. If the relative error in estimating the magnitude of the concentrated force F is 10%, the relative error in measuring the length of the beam L is 5% and the relative error in measuring the diameter D of the beam is 2%, estimate the relative error in the maximum tensile stress o.

The maximum tensile stress o, from bending of a simply supported beam with length L and circular cross section with diameter D, is given by the expression 8FL , where F is the magnitude of a concentrated force acting in the middle of the beam. If the relative error in estimating the magnitude of the concentrated force F is 10%, the relative error in measuring the length of the beam L is 5% and the relative error in measuring the diameter D of the beam is 2%, estimate the relative error in the maximum tensile stress o.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A metal block of cross-section area A and length L is subject to a tensile stress of S. The block elongates by a length of 0.002L. Another block made from the same metal is subject to the same tensile stress. If this block has a cross-section area of 2A and a length of 2L, determine the elongation of the block.
A cantilever beam, 100 mm wide by 270 mm high and 9 m long, carries a load that varies uniformly from zero at the free end to 1300 N/m at the wall., Determine the magnitude of the stress in a fiber 50 mm from the top of the beam at a section 5 m from the free end. Answer must be in MPa.
A 12cm x 16cm air compressor is operated with a maximum pressure of 10 kg/cm2. There are5 bolts with a yield value of 64ksi holding the cylinder head to the compressor. Determine the tensile stress of the bolt.
A metal block of cross-section area A and length L is subject to a tensile stress of S. The block elongates by a length of 0.001L. Another block made from the same metal is subject to the same tensile stress. If this block has a cross-section area of 2A and a length of L, determine the elongation of the block.
A hollow metal tube with an inside diameter of 145 centimeters must carry a tensile load of 670 kilo newton. Determine the outside diameter of the tube, in meters, if the stress is limited to147 Mpa.
In machine design we usually compare the equivalent stress of the component with the: a) Allowable stress b) Machine stress c) Force d) Moment e) Torque
What is the stress in a rectangular rod that is 20 mm by 30 mm in cross-section if is supporting a load of 1000 N? Express your answer in N/m2, Mpa, and psi.
1. A solid piece of metal of volume 10,000 mm3 is compressed by a pressure of 70 MPa. Determine the bulk modulus given that the Young’s modulus E is 214 Gpa and the Poisson’s ratio is 0.33. Also determine the change in the volume.2. Starting from the first principles derive the relation between Young’s modulus (E), shear modulus (G) and Poisson’s ratio (υ)
A solid shaft is transmitting 15 MW of power at 1760 rpm. If the allowable shear stress must not amount to 500MPa, determine the size of the shaft.
A seamless cylinder of storage capacity of 0.03m3 is subjected to an internal pressure of 21 MPa. The allowable stress in the material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.8mm A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.540mm
Consider tow circular rods with a 50mm diameter are joined by a knuckle joint by a pin of 40mm in diameter. If a tensional force of 120kN are applied at each end of the rods, Determine the allowable tensile stress in the circular rods and the Average shear stress occurs in the pin.
The internal loadings at a critical section along the steel drive shaft of a ship are calculated to be a torque of 2300 lb # ft, a bending moment of 1500 lb # ft, and an axial thrust of 2500 lb. If the yield points for tension and shear are sY = 100 ksi and tY = 50 ksi, respectively, determine the required diameter ofthe shaft using the maximum shear stress theory.