Answered: the Nominal Maximum aggregate Size…

the Nominal Maximum aggregate Size (N.M.S) for the aggregate gradation shown below is equal to * Sieve size Passing % 3/4 inch 100 1/2 inch 99 3/8 inch 89 No.4 72 No.8 65 No.30 22 No.200 4

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter4: Mechanical Processes

Section: Chapter Questions

Problem 4.13P

See similar textbooks

Related questions

Q: Sieve Analysis of Fine Aggregates) Students have gathered data for sieve analysis of the following…

Q: A sieve analysis test was performed on a sample of fine aggregate and produced the following…

A: Sieve (mm) Amount retained (g) %Retained Cumulative retain % passing 4.75 0 0 0 0 2.36 33.2…

Q: A sieve analysis test was performed on a sample of coarse aggregate and pro- duced the following…

Q: The sieve analysis results for fine aggregate (1000 g) are shown below, complete the following table…

A: Total weight = 1000 g X = 1000 - remaining weights X = 329 g Fineness modulus = sum of cumulative…

Q: TEST PROCEDURE: 1. Dry the aggregate test sample to a constant weight at a temperature of 110 ±…

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: A sieve analysis test was performed on a sample of aggregate and produced the following results:…

A: Sample calculation: d 0.45= Seive size for 0.45 power gradation curve(d )0.45 = Normal seive…

Q: The mass of a bulk density bucket is measured as 21XY g when it is empty. (Where XY are the last two…

A: Bulk Density of aggregate: The Bulk density of aggregate also known as Unit weight of an aggregate…

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: Volume of bucket =14L=0.494 ft3weight of bucket= 9.21kg=20.20 lbweight of bucket filled with dry…

Q: Let us say you are an aggregate supplier after conducting a sieve analysis you determined that a…

A: Silt and clay particles are very small in size and it is very difficult to separate them from…

Q: An aggregate sample was collected in a container and weighed as 528.7 g. The sample was oven dried…

A: Determine the MC of the aggregates?

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: Given: Volume of bucket, V = 1/3 ft3 Weight of empty bucket, W1 = 18.5 lb Weight of bucket filled…

Q: Aggregates from three sources having bulk specific gravities of 2.753, 2.649, and2.689 were blended…

A: Given data: The specific gravities of three aggregates are 2.753, 2.649 and 2.689. The ratio of…

Q: Three aggregates are to be mixed together in the following ratio: Aggregate A 35% Aggregate B 40%…

A: The following concept and formula are used to determine the percent passing each sieve for the…

Q: Aggregates from three sources having bulk specific gravities of 2.753, 2.649, and 2.689 were blended…

A: Given: For Aggregates from source 1: Specific Gravity = 2.753 Ratio = 70 For Aggregates from…

Q: Calculate the percent voids between aggregate particles that have been compacted by rodding, if the…

A: Void ratio = void ratio of a soil is a ratio of the volume of voids to the volume of solids. e =…

Q: Discuss the process of "Reducing field samples of aggregates to testing size".

A: Large field samples are reduced to smaller field samples to obtain a required size sample for…

Q: The sieve analysis results for fine aggregate (1000 g) are shown below, complete the following table…

Q: A sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced…

A: The given data is shown below:

Q: Sieve size Cumulative retained weight (gm) 3/8 inch No.4 24 No.8 168 No.16 382 No.30 782 No.50 1185…

A: Given: Specific Gravity of Coarse aggregate Sc= 2.61 Specific Gravity of Fine aggregate SF = 2.63…

Q: Based on the data shown in Table P9.31, select the blend for a Superpave design aggregate structure.…

A: Solution: The data of three kinds of blend is shown below: Data Blend 1 2 3 Gmb 2.451…

Q: Three aggregates are to be mixed together in the following ratio:Aggregate A: 35%Aggregate B:…

A: Concept used ( applied ):

Q: Strength requirements, in MPa – 30.68 Mpa Water cement ratio, in decimal – 0.45 Coarse aggregate…

A: Solution: Design of concrete mix for M24 grade The mean strength; fm=fmin+ks=24+1.64x4=30.56 Mpa…

Q: The result of sieve analysis of an aggregate sample is given below. Standard Sieve Size Anount…

A: Sieve Weight Retained Cumulative Weight Retained % Cumulative Wt Retained 63 0 0 0 31.5 2745…

Q: What are the main purposes of Sieve Analysis of aggregates?

A: purpose of sieve analysis Main purpose of sieve analysis is to determine the distribution of…

Q: sand particals does have liquid limit ? justify your answer.

A: Given data Sand particles Lliquid limit To find Does sand has liquid limit

Q: The sieve analysis results of two fine aggregates are given below in Table 1. a) Calculate the…

A: The expression for fineness modulus is given as FA1=∑100-%P100 % passing 100-%passing 100 0…

Q: Calculate the sieve analysis shown in Table P5.20, and plot on a 0.45 power gra- dation chart. What…

A: The given table is shown below:

Q: Sieve Size Amount Retained, Ib 3 in. 2 in. 1-1/2 in. 3.7 1 in. 15.9 3/4 in. 12.0 1/2 in. 13.5 3/8…

Q: Samples of coarse aggregate from a stockpileare brought to the laboratory for determination of…

Q: Three aggregates are to be mixed together in the following ratio: Aggregate A: 35% Aggregate B: 40%…

A: Aggregate percentages in the mix: Aggregate A:35% Aggregate B:40% Aggregate C:25%

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

Q: Samples of coarse aggregate from a stockpile are brought to the laboratory for determinati of…

A: As per guidelines we need to answer only 1st three subparts of question, so please repost rest…

Q: Table shows the grain size distributions of aggregates A, and B. Answer the following questions and…

A: Given: The grain size distributions of aggregates are shown below,

Q: A sieve analysis test was performed on a sample of fine aggregate and produced the results in Table…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: Referring to the aggregate gradations A, B, and C in Figure , answer the following questions:a. What…

A: Consider the figure of aggregate gradations.

Q: Question # 3: Caleulate the fineness modulus of aggregate according to the table of the sieve…

A: Given that:

Q: 2. A sample of fine aggregate weighs 501.2 g when SSD and 491.6 g when OD. The flask weighs 540.6 g…

Q: Aggregate from three sources having bulk specific gravities of 2.90, 2.70, and 2.60 was blended at a…

A: Given,specific gravities,G1=2.90G2=2.70G3=2.60blended ratio=w1:w2:w3=60:30:10let,x=bulk specific…

Q: 25/ Find job mix formula by using mathematical method. Aggregate Specification Sieve Size A B C…

A: The final value of a complete mix design is a preferred mixture of aggregate and asphalt binder.…

Q: The mass of the aggregates to be tested in Los Angeles Abrasion Machine is 10,000g, what is the %…

A: Given:- The mass of the aggregates to be tested = 10,000 g The mass of the aggregate retained in…

Q: if total sample mass of aggregate is 164.9 grams, then the percent passing from sieve size #50 only…

A: The given data is: Total sample mass of aggregates (WT) = 164.9 g

Q: if total sample mass of aggregate is 164.9 grams, then the percent passing from sieve size #30 only…

A: Given:- The total mass of the aggregate sample = 164.9 grams To determine:- The percent passing from…

Q: The table below shows the percent passing for an aggregate blend. Determine the following: 1. The…

A: Hi! Thank you for the question, As per the honour code, we are allowed to answer three sub-parts at…

Q: "A sieve analysis test was performed on a sample of fine aggregate and produced the following…

A: Sr. No. Sieve (mm) Amount Retained (gm) % Retained Cumulative %retained % Passing 1…

Q: From the given data shown in the table below, determine the effective specific gravity of…

Q: 500 gm oven dry fine aggregate was tested to find its physical properties. The output from the test…

A: Solution: Given Data: Weight of dry fine aggregate X=500 gm X1=mass in wet condition 518 gm S=SSD =…

Q: 1. The following data were obtained when sieving a 509.5 g sample of aggregate for an HL 3HS mix.…

A: Solution; Given that; Mass of Aggregate = 1,204.3g Asphalt Content = 7.3%

Q: 5.24 Three aggregates are to be mixed together in the following ratio: Aggregate A 35% Aggregate B…

A: Given:- Aggregate A-35%Aggregate B-40%Aggregate C-25% To find:- Percent passing each sieve for the…

Q: Calculate the percent voids between aggregate particles that have been compacted by rodding, if the…

A: Percentage of voids is the volume of voids occupied by either air or water or combinedly both in the…

Concept explainers

Landfills

The landfill is a site used for the disposal of waste materials. The landfill is a solid waste facility that is often known as a dumping ground. The image below shows a landfill site in Hawaii. Landfilling is the most ancient and common method used for the disposal of waste. For the landfill, a deep trench is constructed in an isolated place away from the city. The trench for landfills is designed properly after analyzing the total population and the waste generation per capita. The waste is dumped into the trench and after every layer of waste, a layer of soil is spread on the top of it.

Question

the Nominal Maximum aggregate
Size (N.M.S) for the aggregate
gradation shown below is equal to
Sieve size
Passing %
3/4 inch
100
1/2 inch
3/8 inch
99
89
No.4
72
No.8
65
No.30
22
No.200
Your answer
4-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

6. Using the ACI/PCA tables, calculate the weight of coarse aggregate dry for 2-CY of a mixture to be placed with a slipform paver if the coarse aggregate is a No.467 stone with a DRUW = 97.8-pcf and the fine aggregate has a fineness modulus of 2.50 (answer to the nearest whole number and provide proper units)
(a) The following data are collected for a modulus ofrupture test on a refractory brick (refer to Equation6.10 and Figure 6,14):F= 5.0 x 10 N.L= 200 mm,h= 130 mm.h= 80 mm.Calculate the modulus of rUpture: (b) suppose thatyou are given a similar rolracioty with the fallSpensin and same dimensions except that its heightSit ts only 60 mm. What would be the load (F) necesary to break this thinner refractory?
What is fractional efficiency curve in a sysclone seperator?
Solution w/FBD
Solution w/ FBD
What is the company's quick ratioA. 1.79B. 1.41C. 2.06D. 1.38
Base course aggregate has a target dry density of 119.7 lb/cu ft in place. It will be laid down and compacted in a rectangular street repair area of 2000 ft * 48 ft * 6 in. The aggregate in the stockpile contains 3.1% moisture.If the required compaction is 95% of the target, how many tons of aggregate will be needed?
Two materials, A and B, are to be separated using two unit operations, 1 and 2. The feed has 10 tons/h A and 4 tons/h B. The split (fraction of material rejected by each operation) is given in Table P5-14. a. Which sequence of operations, (l?2) or (2?1), will yield the greatest recovery of material A? b. What will be the purity of material A using that sequence? c. What will be the efficiency of separation for the entire process train with regard to material A using the Worrell-Stesed equation?
165g water500 g cementStarting time 2:00 pmTemperature at 3:06 pm =24.6 cTemprature at time 3:16 pm=27cWhat is the initial and final setting time? Time penetration 0 0 15 0 25 0 35 0 45 0 55 1 65 2 75 3 85 4
Aggregates from two stockpiles, A and B having coarse aggregate angularity (crushed faces) of 40% and 90% were blended at a ratio of 30:70 by weight,respectively. The percent material passing the 4.75mm sieve was 25% and 55% for stockpiles A and B, respectively. What is the percent of crushed faces of the aggregate blend?
Base course aggregate has a target dry density of 1917 Kg/m3 in place. It will be laid down and compacted in a rectangular street repair area of 600m * 15m * 9.15m. The aggregate in the stockpile contains 3.1% moisture. If the required compaction is 95% of the target, how many tons of aggregate will be needed?
Calculate the absolute volume of fine aggregate in 2-CY of TDOT Class D concrete if fine aggregate weight SSD is 8470-lbs in 7-CY of TDOT Class D concrete and fine aggregate Ss = 2.607 (answer to three places right of the decimal point and provide proper units)