The one line diagram of a simple 3-bus power system shown below. All impedances areexpresses in per unit on a common base. A three phase fault occurs at bus 3 through afault impedance Z =j 0.19 pu, calculate the per unit fault current.A. 1.5 p.u.B.2.5 p.u.G₁j 0.05j0.75j 0.33C. 5.0 p.u.D. 3.0 p.u.G₂ j 0.075j0.452

According to the question, we need to calculate the fault occurred on bus 3 is a three phase fault.

Answered: The one line diagram of a simple 3-bus…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter9: Unsymmetrical Faults

Section: Chapter Questions

Problem 9.35P

See similar textbooks

Similar questions

Equipment ratings for the five-bus power system shown in Figure 7.15 are as follows: Generator G1:Â Â Â Â 50Â MVA,Â 12kV,Â X=0.2 per unit Generator G2: 100Â MVA, 15 kV, X=0.2 per unit Transformer T1: 50 MVA, 10 kV Y/138kVY,X=0.10 per unit Transformer T2: 100 MVA, 15 kV /138kVY,X=0.10 per unit Each 138-kV line: X1=40 A three-phase short circuit occurs at bus 5, where the prefault voltage is 15 kV. Prefault load current is neglected. (a) Draw the positive-sequence reactance diagram in unit on a 100-MVA, 15-kV base in the zone of generator G2. Determine (b) the ThĂ©venin equivalent at the fault, (c) the subtransient fault current in per unit and in kA rms, and (d) contributions to the fault from generator G2 and from transformer T2.
Equipment ratings for the four-bus power system shown in Figure 7.14 are as follows: Generator G1: 500 MVA, 13.8 kV, X=0.20 per unit Generator G2: 750 MVA, 18 kV, X=0.18 per unit Generator G3: 1000 MVA, 20 kV, X=0.17 per unit Transformer T1: 500 MVA, 13.8/500YkV,X=0.12 per unit Transformer T2: 750 MVA, 18/500YkV,X=0.10 per unit Transformer T3: 1000Â MVA, 20/500YkV,X=0.10 per unit A three-phase short circuit occurs at bus 1, where the prefault voltage is 525 kV. Prefault load current is neglected. Draw the positive-sequence reactance diagram in per unit on a 1000-MVA, 20-kV base in the zone of generator G3. Determine (a) the ThĂ©venin reactance in per unit at the fault, (b) the subtransient fault current in per unit and in kA rms, and (c) contributions to the fault current from generator G1 and from line 1-2.
With the same transformer banks as in Problem 3.47, Figure 3.41 shows the oneline diagram of a generator, a step-up transformer bank, a transmission line, a stepown transformer bank, and an impedan load. The generator terminal voltage is 15 kV (line-to-line). (a) Draw the per-phase equivalent circuit, aounting for phase shifts for positive-sequence operation. (b) By choosing the line-to-neutral generator terminal voltage as the reference, determine the magnitudes of the generator current, transmiss ion-line current, load current, and line-to-line load voltage. Also, find the three-phase complex power delivered to the load.

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning