The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares, each with a cross-sectional area of 340 mm2. bar (1) has a length L1 = 810 mm and bar (2) has a lenght L2 = 1080 mm. Assume dimensions of a = 480mm, b = 38mm, and c = 600mm. If the allowable normal stress in bars (1) and (2) must be limmited to 165 MPa each, determine: a) the maximum load P that may be applied at D to the rigid bar.                                                                               b) The deflection at D for the load determined in part (a).

Q: A 0.2833?? drum contains saturated vapor @ 37.77°C. What are the pressure and mass of vapor in the  ...

A:

Q: An eyed plate & pin is assembled as illustrated and are subjected to an opposing force of 10kN. The ...

A:

Q: A rigid tank of constant volume contains 100 kg of water which is churned by a paddle driven by a mo...

A:

Q: In a catalytic converter in an automobile, the reaction of carbon monoxide with oxygen produces ____...

A: In a catalytic converter in an automobile, the reaction of carbon monoxide with oxygen produces carb...

Q: Conduct FTA(Fault Tree Analysis) for the hydrogen gas station. You should have at least 4 basic eve...

A: Given : To find: Fault tree analysis

Q: 0.76 m^3 tank is to be filled with saturated vapor at 12.34 bar. determine the mass necessary and it...

A: Given Data V=0.76 m3 sat. Vapor P=12.34 bar

Q: Pa. The required gauge pressure is

A: To find gauge pressure

Q: Suppose by curiosity, a student poured three different media inside a transparent tank with gauge re...

A: Principle : Pascal law - states that, pressure on the horizontal plane of same fluid remains same.

Q: A cylindrical metal tube of mean radius r = 5 in., length L = 14 ft, and shear modulus G =  11 x 106...

A:

Q: A rigid tank of constant volume contains 100 kg of water which is churned by a paddle driven by a mo...

A:

Q: A fuel is represented with C5H8 is burned with 40% excess air. If mass of fuel is 0.17kg, find the m...

A: GivenC5H8masss=0.17kg40% excess air required.

Q: What are control lines and how do they function?

A:

Q: 5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angul...

A:

Q: T

A: No answer

Q: A glass tube is attached to a water pipe, as shown in the figure. If the water pressure at the botto...

A:

Q: the water level in a PWR must always be above the top of the active core. a. Estimate the decay heat...

A: How much rot heat being produced in a fuel gathering whenever after closure can be determined in two...

Q: Gzd If (h=o.7 cm) for weld , find (Imax) for figure blow: l00 225mm of f=400W +50mm 45.27 Mlam? answ...

A: Given Data The force acting in the downward direction is: F=400 N The height of the weld is: h=0.7 ...

Q: A closed tank contains 0.5 m of mercury, 1.5 m of water, 2.5 m of oil of specific gravity 0.8 and ai...

A: A closed tank includes 0.5 m of mercury, 1.5 m of water, 2.5 m of oil with a specific gravity of 0.8...

Q: (a) Consider steam at 300C and 10 bars of pressure. During adiabatic expansion through a turbine, th...

A:

Q: A 0.76m^3 tank is to be filled with saturated vapor at 12.34 bar. Determine the mass necessary and i...

A: Given Data: The volume of the tank, V=0.76 m3 Pressure, P=12.34 bar

Q: Consider laminar flow of a Newtonian fluid between two parallel plates as shown in the figure. Devel...

A: Given data: uy=4umaxyh-yh2 Need to drive the formula for the drag force exerted on both plates.

Q: The volume flow rate of water that recirculates from the blade outlet to the impeller is estimated t...

A:

Q: Questions: 1) Explain Continuous casting process with a neat diagram?

A:

Q: Find the magnitude of the two components of F directed along AB * .and AC

A:

Q: 2.x {x: (x- 2)(x+1) - 20}

A:

Q: A liquid has a mass of 1500 kg with a total volume of 0.853 m3. Find: The weight of the liquid in ...

A:

Q: A steady stream of air enters a horizontal compressor at the rate of 0.02 kg/s. The air temperature ...

A: During a steady-flow process, the total energy content of a control volume remains constant i.e., EC...

Q: A uniform bar of length L, cross-sectional area A, and mass density p is suspended vertically from o...

A:

Q: A core was mounted in a gas permeameter to measure permeability. Determine the liquid permeability (...

A:

Q: The gate is b=5m wide, is hinged y = 10050N/m³ at point B, and rest against a 15m smooth wall at poi...

A:

Q: A pump delivers 2000kg/min of water (50°C) from reservoir A (El. 10m) to reservoir B (El. 40m). The ...

A: given; mass flow rate of water (m)=2000kg/min                                         =33.33kg/selev...

Q: Saturated liquid has a specific volume of 0.05048 m3/kg. What are the pressure, temperature, specifi...

A: Given that, Specific volume at saturated liquid, v=0.05048 m3/kg From the steam table  Maximum speci...

Q: How much work is necessary to compress air in an insulated cylinder from 0.10m3 to 0.01 m3? Use T1 =...

A: Question: How much work is necessary to compress air in an insulated cylinder from 0.10m3 to 0.01 m3

Q: Determine the resultant of the forces as shown below when B = 50°. %3D

A: To find resultant of forces

Q: A simple rankine ideal cycle with water as the working fluid. Twenty kilograms of steam enters the t...

A:

Q: Write a CNC part program to for cutting a sheet metal part for fabrication as shown in the figure be...

A: CNC is an abbreviation for computer numerical control programming, which is utilised in the machinin...

Q: 6. Which of the following is a trait of stationary-blade rotary compressors? A. The blade is mounted...

A:

Q: QUESTION 4 The following figure represents a cross section through a long opening. The magnitudes of...

A:

Q: (d) 2x² + 9x +4>0

A:

Q: A gate is used to hold water as shown in the figure, Ignore the weight of the gate and the friction ...

A:

Q: I am trying to figure out how much heat is gained through a 1 ft^2 glass windowpane with the above s...

A: Given   Area, A = 1 ft2               = 0.0929 m2 Temperature, T = 35oC                          = 3...

Q: Heat transfer problem Water flows through a thin-walled cylindrical tube of diameter 1 cm, maintaine...

A:

Q: For final answers: h and u (correct to 2 decimal places), s and v (correct to four decimal places). ...

A: Given   Volume, V = 0.76 m3 Pressure, P = 12.34 bar Find   Enthalpy, h   Entropy, s   Specific volum...

Q: 3. Three kids stand on a see-saw as shown. The see-saw has a uniform cross section and weighs 10 lb,...

A: Given Data  mA= 30 lb mB= 40 lb mC=20 lb

Q: 5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angul...

A:

Q: 9-1-38 [reheatGen-10MPA] A steam power plant operates on an ideal reheat-regenerative Rankine with o...

A:

Q: A rigid tank containing air is subjected to a reversible process in which it is heated from its init...

A: Given data: T1=600 KP1=1.5 barP2=4.352 psi=0.3 bar Need to determine the specific change in entropy.

Q: By passing thru a turbine radius of 50meters, the KE of the air is transformed to work. To produce 1...

A:

Q: A truncated conical pivot bearing which supports an axial load of 20000N from a vertical shaft rotat...

A: Given that : Axial load, W=20000 N, Speed of shaft, N=180 rpm            ∴ ω=2πN60=2π×18060=18.84 ra...

Q: Determine F12 and F21 for the following configurations using the reciprocity theorem and other basic...

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.