The piston rod of an air operated press has a length of 2500 mm, with its right-hand end pin connected to the operating lever and the piston end of the rod fix ended. The rod is made of a material whose Sy = 250 MPa and E = 200 GPa. For a factor of safety of 3.5, determine the maximum safe compressive load of the rod in Newtons if its diameter is 47.5 mm. Round your answer to 4 significant figures.

The piston rod of an air operated press has a length of 2500 mm, with its right-hand end pin connected to the operating lever and the piston end of the rod fix ended. The rod is made of a material whose Sy = 250 MPa and E = 200 GPa. For a factor of safety of 3.5, determine the maximum safe compressive load of the rod in Newtons if its diameter is 47.5 mm. Round your answer to 4 significant figures.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.1P: A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness...

See similar textbooks

Similar questions

A long solid steel bar of uniform 1.25 in diameter has a 0.375 in diameter hole at its center with its axis perpendicular to the length of the shaft. A tensile load of 108,000 lb is applied longitudinally to the bar. Determine the probable material that can be used for this load for a factor of safety of 5
Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and made of aluminum that has anelastic modulus of E = 12,000 ksi. Determine the maximum magnitude of load P that can be applied to the rigid bar withoutcausing member (1) to buckle
PLS ANSWER ASAP TY! For the assembly shown, a yoke on a 30 mm diameter rod is attached to a 25 mm thick bracket via 15 mm diameter bolt as shown. The ultimate axial strength in the 30 mm dia. rod is 150 MPa. a)Determine the largest load P (in KN) that can be applied to the rod if a factor of safety of 2.5 with respect to the ultimate axial strength is required. b) What is the tensile axial stress on the rod (in MPa)? c) What is the shear stress on the bolt (in MPa)? d) What is the factor of safety for the 15 mm. dia. bolt with respect to the ultimate shear strength? (in 2 decimal places)
Refer to the set of bars made of a material with a yield strength of 350 MPa, determine the minimum dimensions h1 and h2 required. Apply a safety factor FS = 1.5 without flux. Each bar is 12 mm thick
A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 50 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 160 kN determine the load carried by the steel rod and the brass bush and the compressive stress set up in each material. For steel, E = 210 GN/m2; for brass, £ = 100 GN/m2
A large water tank that has a capacity to carry 20,000 liters is to be supported by four cylindrical posts. These four support posts are made of plain carbon (1045) steels with the yield and tensile strengths of 310 MPa and 565 MPa, respectively. Determine the minimum required diameter of the post assuming a factor of safety of 5.
An aluminum strut 2.50m long has a rectangular section 60mm by 30mm. A bolt through each end secures the strut so that it acts as a hinged column about an axis perpendicular to the 60 mm dimension and as a fixed ended column about an axis perpendicular to the 30mm dimension. Determine the safe central load using a factor of safety of 2.5 and E = 70 Gpa.
Determine the thickness of a 130 mm wide uniform plate for safe continuous operation if the plate is to be subjected to a tensile load that has a maximum value of 260 kN and a minimum value of 110 kN. The properties of the plate material are as follows: Endurance limit stress = 235 MPa, and Yield point stress = 310 MPa. The factor of safety based on yield point may be taken as 1.4.
A circular-cross-section bar with a diameter of 50mm and a length of 1.25 m is axially loaded. The baris made of medium-carbon steel. Both ends are pinned.Determine(a) Whether the Johnson or the Euler formula shouldbe used.(b) The critical load.
Determine the parameters for each question below, assume E = 200 GPa.i) Critical load for the square columnii) Radius of the round column for which both columns have the same critical loadiii) Express the cross-sectional area of the square column as a percentage of thecross-sectional area of the round column.
Why is is that when I compute for the diameter, the answer is 7.9706? How was 13.22 obtained? Bartleby link for solution: https://www.bartleby.com/questions-and-answers/a-steel-rod-is-stretched-between-two-rigid-walls-and-carries-a-tensile-load-of-5000-n-at-20c.-if-the/5c99ed3b-d083-41be-a905-b15aa3bc8648
Determine the diameter of a brittle member in inches if the tensile design load is 15,671 lb. assuming a factor of safety of 5 based on an ultimate strength of 60,000 psi.