Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and made of aluminum that has an elastic modulus of E = 12,000 ksi. Determine the maximum magnitude of load P that can be applied to the rigid bar without causing member (1) to buckle

Q: A steel column (E = 200 GPa) is 9 m long, embedded in a one end and supported on the other. If the…

A:

Q: Each of the five struts shown consists of a solid steel rod. (a) Know-ing that strut (1) is of a…

A: Given data: *The length of the strut are L=900 mm. *The diameter of the first strut is d1=0.8 in.…

Q: Question 3 A column of 7 m effective length is to be made by welding two 228 x 12 mm plates to a…

A: Given: The length of column, Le = 7 m The elastic modulus, E = 200 GPa The moment of inertia about…

Q: Problem: A 7.2-m long A-36 steel tube having the x-section shown is to be used a pin-ended column.…

A:

Q: Bronze E = 83 GPa • 100 mm Steel E = 200 GPa O 80 mm 1,200 kN 900 kN A 3 m; 2.50 m

A: FBD of bar AB:- FBD of bar BC:-

Q: A metal bar AB of a weight W is suspendedby a system of steel wires arranged as shown in thefigure.…

A: Given:   Let,L=Length of side perpendicular to bar=5ina=Length of side parallel to bar=2inHypotnuse…

Q: Two solid bars support a load Pas shown. Bar (1) has a cross-sectional area of A₁ = 4350 mm² and an…

A: To find: The maximum load that can be supported by the structure without exceeding either allowable…

Q: A spreader bar is used in the assembly shown in the figure attached. It is made of a circular steel…

A: GIVEN:*spreader bar of diameter 32mm. * Both end of the spreader bar may be assumed to be pin…

Q: A stainless steel tube with an outside diameter of 50 mm and a wall thickness of 5 mm is used as a…

A:

Q: Q.1: The two-bar truss ABC shown below has pin supports at points A and C, which are 2.0 m apart.…

A: Given: The truss ABC is shown below: Maximum tension in tension and shear are 125 Mpa and 45 Mpa.

Q: An aluminum strut 2 m long has a rectangular section 20 mm by 50 mm. A bolt through each end secures…

A:

Q: Two solid bars support a load Pas shown. Bar (1) has a cross-sectional area of A 3650 mm2 and an…

A: Stress is a physical mass that expresses the inner forces of a continuous material exerted upon each…

Q: 4) A 15ft W12x40 steel column is supported by a steel base plate, concrete pedestal and concrete…

A: Given: length of the steel column=15ft=180in cross sectional area of the columnA=11.7 in2 axial…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 3200 mm² and an…

A: To Find : The maximum load Pmax. Given :  The cross section area of bar 1 is  A1=3200 mm2 The cross…

Q: A 3.5-m long column with rectangular cross section of 4 cm x 3 cm is under an axial compressive load…

A:

Q: THe bracket shown is made of cold drawn steel with Sy=400MPa and Su=480 MPa, and is fastened to a…

A:

Q: A 2-m length of an aluminum pipe of 240-mm outer diameter and 10-mm wall thickness is used as a…

A: Assumptions Material is homegenous and isotropic Material follows hooks law Given data Length of the…

Q: Determine if the following column is long or short, and then determine the critical load on a steel…

A:

Q: 8. Select the lightest W shape that will act as a column 12 m long with fixed ends and support an…

A: To find : select the lightest shape that will act column. Given : axial loadP=700 KN proportional…

Q: An aluminum strut 2.50m long has a rectangular section 60mm by 30mm. A bolt through each end secures…

A:

Q: Two members AB and AC are made of material with E= 138 Gpa and each member has cross sectional area…

A:

Q: Member AB consists of a single C130 x 10.4 steel channel of length 2.5 m. Knowing that the pins at A…

A: Given data: Channel length, l=2.5mYoungs modulus, E=200GPa

Q: 2. Link BD is made of brass ( E = 103 GPa ) and has a cross-sectional area of 258 mm?. Link CE is…

A:

Q: SA steel tube of 80-mm outer diameter is to carry a 93-kN load P with an eccentricity of 20 mm. The…

A:

Q: The rigid bar of negligible mass, pinned at one end, is supported by a steel rod and aluminum rod as…

A:

Q: mm. The normal stress in the aluminum rod must be limited to 124 MPa, and the normal stress in the…

A: From the given data:

Q: A 20-mm-diameter rod made of the same material as rods AC and AD in the truss shown was tested to…

A:

Q: A straight girder of uniform section and length L rests on supports at the ends, and is propped up…

A:

Q: 2. Link BD is made of brass ( E = 103 GPa ) and has a cross-sectional area of 258 mm?. Link CE is…

A: Answer: The maximum force P that can be applied vertically at point A is 13.37815 kN.

Q: Two solid bars support a load Pas shown. Bar (1) has a cross-sectional area of A1 = 2350 mm2 and an…

A:

Q: 400-m bar of 16 x 60-mm rectangular crosSs section consists of two mild-steel layers, each 5 mm…

A: Given dataE=200GPaδm=1.4σ1(mild Steel)=240MPaσ2(tempered steel)=600MPaL=400mm ***As per our company…

Q: Two solid bars support a load Pas shown. Bar (1) has a cross-sectional area of A1 = 2600 mm2 and an…

A:

Q: A 1-inch brass round bar is to be used as a support for a frame. Determine the maximum load that the…

A:

Q: Given the assembly shown is a cylinder rod position vertically and is supported by a collar and a…

A: Shear failure between collar and cylinder: Area of shear occurs between collar and cylinder…

Q: A compression member of 1.5-m effective length consists of a solid 30-mm-diameter brass rod. In…

A: Step : I Given: E = 200GPA do = 30mm d = 15mm To find : a ) The percent reduction is critical load…

Q: 2. Link BD is made of brass (E = 103 GPa ) and has a cross-sectional area of 258 mm?. Link CE is…

A:

Q: A rectangular wooden column (E = 12 GPa) of 3 m have as dimensions shown. Determine a critical load…

A:

Q: Determine the largest load P that can be applied to the structure shown below. All members are made…

A:

Q: 4. A load of 25 KN is to be supported by three equidistant vertical rods as shown. At first, all the…

A: To find: The stress in the rods. Given: The young modulus of steel is Esteel=205 GPa and Ecopper=100…

Q: 2. The gray plastic block shown is bonded to a fixed base and to a horizontal rigid plate (black…

A: Given: Applied load = 9 kips G = 50 ksi

Q: A column with the cross section shown has a 13.5-ft effective length. Using a factor of safety equal…

A: Given Data The effective length Le = 13.5 ft = 162 inch         ( 1ft =12 in ) The young modulus of…

Q: 1. Column ABC shown has a uniform rectangular cross section and is braced in the x plane at its…

A: The factor of safety,FOS=2.7 Load,P=5.4×103N Length,L=600mm Modulus of Elasticity,E=70GPa=70×109Pa

Q: Rigid beam ABC is supported by a pinned connection at A and by a 190 mm by 190 mm square timber post…

A:

Q: 7 ft 5 ft 8 ft The assembly shown above includes column AB, which has the following properties: •…

A: Option c is correct.

Q: The horizontal link BC is 1/4 in. Of thickness and width w = 1.25 in., It is made of steel with an…

A:

Q: 4. A load of 25 KN is to be supported by three equidistant vertical rods as shown. At first, all the…

A: Given data as per the question Load =25 KN Additional load = 20 KN Young modulus of steel = 205 Gpa…

Q: .21 The uniform brass bar AB has a rectangular cross section and is supported by pins and brackets…

A: Given                    Length, L = 2 m                    Height, d = 38 mm   Young's modulus, E =…

Q: 12. A% in. -diameter rod made of the same material as rods AC and AD in the truss shown was tested…

A:

Q: Determine the largest load P (in KN) that can be applied to the rod if a factor of safety of 2.5…

A: load applied on rod =25kN ultimate tensile strength of pin material =100 MPa Ultimate tensile…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.