The plastic distorts as shown by the dashed lines. (Figure 1) The dimensions are L= 460 mm H =310 mm di =2 mm, d2 =5 mm, dz = 15 mm, d4 =8 mm, d; =2 mm, and de = 5 mm. Part A Determine the shear strain Yry at corner C. Express your answer to three significant figures and include appropriate units. (yc)zy = Value Units igure < 1 of 1> Submit Request Answer dz Part B B Determine the shear strain yzy at corner D. Express your answer to three significant figures and include appropriate units. H HA ? D Value Units

The plastic distorts as shown by the dashed lines. (Figure 1) The dimensions are L= 460 mm H =310 mm di =2 mm, d2 =5 mm, dz = 15 mm, d4 =8 mm, d; =2 mm, and de = 5 mm. Part A Determine the shear strain Yry at corner C. Express your answer to three significant figures and include appropriate units. (yc)zy = Value Units igure < 1 of 1> Submit Request Answer dz Part B B Determine the shear strain yzy at corner D. Express your answer to three significant figures and include appropriate units. H HA ? D Value Units

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
. Define the terms shear stress and shear strain, illustrating your answer by means of a simple sketch. Two circular bars, one of brass and the other of steel, are to be loaded by a shear load of 30 kN. Determine the necessary diameter of the bars (a) in single shear, (b) in double shear, if the shear stress in'the two materials must not exceed 50 MN/m 2 and 100 MN/m z respectively. [27.6, 19.5, 19.5, 13.8 ram.] Can you please show a full solution explaining what * means if you are using it thanks
(a) Define centroidal axes, principal axes and neutral axes with the help of diagrams. When do these axes coincide? (b) Define longitudinal and hoop stresses in a thin walled in thin walled pressure vessels. Support your answer with neat sketches. (c) Define strain gauge. Discuss strain rosettes and its various types. (d) Define Kern of a section. Derive the general equation for finding the kern of a section.
The cross section of a concrete corner column that is loaded uniformly in compression is shown in the figure. A circular pipe chase cut-outof 10 i n. in diameter r tins t he height of t he co \u m n (see figure).(a) Determine the average compression stress crr in the concrete if the load is equal to 3500 kips.(b) Determine the coordinates x and y{of the point where the resultant load must act in order to produce uniform normal stress in the column.
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. (Where P is equal to 51kips)
A rod with a diameter of 13 mm and a length of 50 mm is subjected to a force of 50 kN. The diameter is reduced to 12.99265 mm. Determine: a. The modulus of elasticity. Answer: 200 GPa. b. Poisson's ratio. Answer: ν = 0.30 c. Shear modulus. Answer: G = 76.92 GPa. d. The deformation of the rod. Answer: δx = 0.09415 mm. Recommendation: Obtain the modulus of elasticity using the slope of the straight line.
The bronze bar 3 m long with a cross-sectional area of 350 mm2 is placed between two rigid walls. At a temperature of –20°C, there is a gap of 2.2 mm, as shown below. Determine the temperature in °F at which the compressive stress in the bar will be 30 MPa. Use α =18(10)-6/°C and E = 80 GPa. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
The modulus of elasticity is measured as the secant for a stress at: a) 30% b) 45% c) 25% d) 40%
3 DECIMAL PLACES 1. what is the axial stress in the bronze rod (MPa)? first pic 2. what is the maximum tangential stress (MPa) if the internal pressure is 1.8 MPa and the wall thickness is 13mm? second pic
Define the following:a. Proportional limitb. Elastic limitc. Yield stress
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. where P=25 .