The power output of a steam turbine is 5 MW. The inlet conditions are 2 MPa of pressure, 400 degrees * C of temperature, 50 m/s of velocity and 10 m of elevation. The exit conditions are 15 kPa, 0.9 dry quality, 180 m/s and 6 m elevation. Compute: (i) The magnitude of A h, A ke, Ape, (ii) Work done per kg of steam,

The power output of a steam turbine is 5 MW. The inlet conditions are 2 MPa of pressure, 400 degrees * C of temperature, 50 m/s of velocity and 10 m of elevation. The exit conditions are 15 kPa, 0.9 dry quality, 180 m/s and 6 m elevation. Compute: (i) The magnitude of A h, A ke, Ape, (ii) Work done per kg of steam,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In Fig. water exits from a nozzle into atmosphericpressure of 101 kPa. If the fl ow rate is 160 gal/min, what isthe average velocity at section 1?( a ) 2.6 m/s, ( b ) 0.81 m/s, ( c ) 93 m/s, ( d ) 23 m/s, ( e ) 1.62 m/s
Q1/1In a single-stage axial flow gas turbine of A319 Airbus Airplane has an axial velocity is equal to 250 m/s, and assume equal inlet and outlet velocities. Stage exit swirl angle is 9° , mass flow rate of gas is 15 kg/s, and nozzle efflux angle is 63°. Assume that blade speed is 350 m/s, gas enters at stagnation pressure of 5 bar, and stagnation temperature of 1980 °R. Also, assume y = 1.33, and C,,=1.147 kJ/kg. K. Determine the rotor blade gas angles, output power, blade-loading coefficient, and degree of reaction.
In a turbine system, states A and B are homologous. If the net head ratio HA/HB =16 , volume flow rate ratio VA˙/VB˙=9. What is the diameter ratio DA/DB ? a) 3/2 b) 6 c) 12 d) 2/3
A pump delivers gasoline at 20 degrees Celsius and 12 (m^3)/h. At the inlet p1=100 kPa, z1=1 m, and V1=2 m/s. At the exit p2=500 kPa, z2=4 m, and V2=3 m/s. How much power is required if the motor efficiency is 75 percent?
Steam flows through a turbine at the rate of 100 lb/min with ∆KE = 0 and Q = 0. At entry, its pressure is 175 psia, its volume is 3.16 ft3/lb, and its internal energy is 1166.7 Btu/lb. At exit, its pressure is 0.813 psia, its volume is 328 ft3/lb, and its internal energy is 854.6 Btu/lb. What horsepower is developed? (b) The same as (a) except that the heat loss from the turbine is 10 Btu/lb of steam.
Steam enters a convergent-divergent nozzle at 11 bar, dry saturated at a rate of 0.75 kg/sand expands isentropically to 2.7 bar. Neglecting the inlet velocity, and assuming theexpansion follows a law, pv1.135 = constant, calculate the area of the nozzle throat and thearea of the nozzle exit.
Steam enters a horizontal turbine at 350 lbf/in 2 absolute,580 ° C, and 12 ft/s and is discharged at 110 ft/s and 25 ° Csaturated conditions. The mass fl ow is 2.5 lbm/s, and theheat losses are 7 Btu/lb of steam. If head losses are negligible,how much horsepower does the turbine develop?
4. Air flows isentropically through the channel To = 300 ° C. both ends have an identical area that is A = 25 cm², pressure p1 = 120 kPa and p2 = 60 kPa. Determine : a). Mass flow rate, b). Throat area C). Ma2
a=2 , b=1 The properties of the air in the inlet section with A1 = 0.25ab m2 in a converging-diverging channel are given as U1 = 25a,b m/s, T1 = 3ab K, P1 = 13a,b kPa (absolute). Find the required cross-sectional area, pressure, temperature, velocity and mass flow rate to obtain sonic (Ma2=1.0) flow at the outlet. Calculate critical values of A*, U*, T*, P*. Solve the problem by making the necessary assumptions and drawing the schematic figure.
EX1: Given are the following data for a commercial centrifugal water pump: r1 =10 cm, r2 = 17.5 cm, By =30°, B2 =20°, speed =1440 r/min. Estimate (a) the design point discharge, (b) the water horsepower, and (c) the head if by = b2 = 4.4 cm.(Hint. design point discharge, i.e 11=90°)
Each stage of an axial-flow compressor is 0.5 reaction,, has the same blade speed and the same flow outlet angle of 30 deg relative to the blades. the mean flow coeficcient is constant for all stages at 0.5. At entry to the first stage the stagnation temperature is 278 K, the stagnation pressure 101.3 kPa, the static pressure is 87.3 kPa and the flow area 0.372 m2. Using compressoble flow analysis determine the axial velocity and the mass flow rate. Determine also the shaft power needed to drive the compressor when there are 6 stages and the mechanical efficiency is 0.99.
Assuming the clearance is negligible for a single stage compressor with the following data.Atmospheric pressure: 90 kPaAtmospheric temperature: 17 ˚CDelivery pressure: 7 barFree air delivery flow rate: 0.2 m3/min Take “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K 1.What is the power input to the compressor if compression is isentropic in kW to 3 decimal places?