The principal tensile stress at a point across two mutually perpendicular planes are 100 N/mm2 and 40 N/mm2. The normal, tangential and resultant stresses on a plane inclined at 20° to the axis of the minor principal stress by analytical method is

The principal tensile stress at a point across two mutually perpendicular planes are 100 N/mm2 and 40 N/mm2. The normal, tangential and resultant stresses on a plane inclined at 20° to the axis of the minor principal stress by analytical method is

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Related questions

Q: (i) determine the magnitudes of the principal stresses. (ii) determine the directions of the…

Q: Q2: For the element shown in Figure 2. Use the data from Table 2 Determine the following: 1. The…

A: A perpendicular force applied on a body per unit area is referred to as a stress. There are three…

Q: The state of stress of an element is given. Determine its principle plane by the specialized…

Q: 6o mm A GIVEN: G =386 MDa T=25KN.m ìM=13KN- m 4 I- 폭(울)+, J= 폭을 Q1. DRAW STRESS STATES AT A IN X-Y…

A: Given, σy=386 MPaT=2.5 kN.m=2500 N.mM=1.3 kN.m=1300 N.md=60 mm=0.06 m

Q: the associated normal stresses and show the results

Q: For the plane stress state listed below, draw a Mohr's circle diagram properly labeled. Keep in mind…

A: Given Data σx=20 kpsiσy=-10 kpsiτxy=-8 kpsi Draw the diagram

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress, Each grid…

Q: (a) the principal stresses and the positions of the plane on which they act (b) the position of the…

A: here all angle measure from vertical plane and in counter clock wise direction, if in calculation…

Q: Mechanics of Materials Two forces are applied to the 100 mm diameter plate attached to the 40 mm…

A: Given: The loads on the shaft is shown below:

Q: Q3. A thin rectangular plate of thickness t is subjected to stresses that can be represented by the…

Q: Q2 Figure Q2 shows few loadings applied on bar ABD. Suppose the diameter of the bar is A mm, and…

Q: you can provide handwritten solution also. At a point in a material under stress, the intensity of…

A: Normal stress acting on principal plane is known as a principal stress. The plane at which no shear…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

Q: The stress at a point of a machine component are 200MPa tensile and 100MPa compressive. Using Mohr’s…

A: Given: σx=200 MPaσy=-100 MPaτxy=0θ=30°

Q: An elastic body is subjected to a tensile stress X in a particular direction and a compressive…

Q: Direct stresses of 120 N/mm2 (tension) and 90 N/mm2 (compression) are applied at a particular point…

A: Given data: The direct stresses in mutually perpendicular direction are σx=120 Nmm2 and σy=-90…

Q: 2. At a point in a brocket, the stresses on two mutually perpendicular planes are 180 MN/m?…

Q: Q.1) For the given state of stress at a point (Normal stresses are 200 & 150 MPa, and Shear stress…

A: Given data:6x=-200MPa6y=-150MPa → compressive normal stressτxy=100MPaθ=30°To find:1) Normal…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

Q: In a biaxial state of stress, normal stress are 900 N/mm^2 and 100 N/mm^3 in x and y diretion…

A: Given data σx=900 MPaσy=100 MPaτxy=300 MPa

Q: For the given state of stress below, 1- determine the principal stresses, the in-plane maximum shear…

A: here, for first part use the principal stress and max. shear stress equation. for 2nd and 3rd parts,…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

Q: The state of plane stress at a point is represented by the element as shown in Figure Q2. The state…

Q: The state of stress at a point, for a body in place stress, is shown in the figure below. If the…

Q: At a point in a strained material, the intensities of normal stresses on two planes at right angles…

A: Find the principal planes and principal stresses also find maximum shear stress.

Q: (tensile), minor stress of 40 MPa (tensile) along with a counter clockwise shear stress of 30 MPa.…

Q: For the stress state shown in the figure below, use the Mohr’s circle method to determine (a) the…

A: This is a case of pure shear,therefore, Radius of the mohr circle…

Q: A point on a thin plate is subjected to the two stress components as shown in the figure below. a.…

Q: The state of an element is shown in figure Fig. - 1. Use to find the stresses and planes of stress…

A: The Mohr's circle is nothing but the representation of the stresses in the material on a circle. The…

Q: At a point in an elastic material under strain, the stresses on the three mutually perpendicular…

A: Given: Normal tensile and shear stress on one plane are 60 N/mm2 and 40 N/mm2. Normal tensile and…

Q: 2) The state of stesss at a point in a body relative to the xyz coordinate system is: -2 3 -5 [G]= 3…

Q: A rectangular block of material is subjected to a tensile stress of 90 N/mm2 along X axis and a…

A: Given data: - The tensile stress on the block is σx = 90 N/mm2. The compressive stress on the block…

Q: For the element shown below, determine: 1- The principal stresses and the maximum in-plane shear…

A: A perpendicular force applied on a body per unit area is referred to as stress. There are three…

Q: Consider the 2-D state of stress shown below. Using the provided scales graph the Mohr's Circle for…

A: Solution: All the parts have been answered below with necessary explanation:

Q: QJThe state of plane stress at a point is represented by the stress element below: A. Draw the…

A: According to the company's guidelines when multiple sub parts are asked only first 3 has to be…

Q: At a certain point in an elastic body direct stresses of 150 N/mm² tensile and 100 N/mm² compressive…

A: Given:σx=150N/mm2σy=-100N/mm2Principal stress, σ1=180N/mm2

Q: 3. At the point labeled A in the bracket below, the stresses are og = 4.8 ksi, o, = -1.2 ksi and Ty…

Q: For the state of plane stress, stress components are shown on the element in Figure Question 1: a)…

Q: 3. Listed below is a combination of stresses acting at a point and referred to axes x and y in an…

Q: Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: Given data as per question Each grid slide=16 MPaFor a point in a physical object that is subjected…

Q: 1) For the state of stress shown in figure, use the Mohr's circle method to determine (a) The…

Q: 50 MPа B 80 MРа 80 MPа A 25 MPа 50 MPа

Q: At a point in a piece of elastic material, direct stresses of 92 MN/m2 tensile and -49 MN/m2…

Q: 8.7 At a point in a material under stress, there is a compressive stress of 200 MN/m and a shear…

Q: A certain point in the mechanical part has shearing and normal stresses measured in MN/m^2 as shown…

A: In Mohr's circle we take a suitable scale to construct the circle. Accordingly we draw the circle.

Q: Mohr's Circle The major and minor principal stresses acting at a point are 80 psi compression and 20…

A: A) To Draw : The Mohr's circle for this stress combination. Given: The major principal stress…

Question

The principal tensile stress at a point across two mutually perpendicular planes are 100 N/mm² and 40 N/mm². The normal, tangential and resultant stresses on a plane inclined at 20° to the axis of the minor principal stress by analytical method is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The normal and tangential stresses on a plane inclined at 30° to the axis of the minor principal stress are 75 N/mm2 and 20 N/mm2. The resultant stress on a plane by analytical method is
A plane stress state is given by the principal stresses σx =25 MPa and σy= -11 MPa. Determine σx' in the case that the system is inclined by 30 degrees (counter-clockwise). Give your answer in MPa to the nearest whole number.
At a point in an elastic material under strain, the stresses on the three mutually perpendicular planes are as follows:A normal tensile stress of 60 N/mm^2and shear stress of 40 N/mm2 on one plane and a normal tensile force of 40 N/mm^2and a complimentary shear stress of 40 N/mm^2 on another plane. Find the following using Mohr circle only (take 5 N/mm2 = 1 cm)a. The principal stresses and principal planes.b. The maximum shear stress and its plane.c. The normal and shear stress on a plane inclined at an angle of 30Oto major principal plane.
A rectangular block of material is subjected to a tensile stress of 90 N/mm2 along X axis and acompressive stress of 45 N/mm2 on a plane at right angle to it, together with shear stresses of80 N/mm2 on the same plane. Calculate the direction of principal planes, the magnitude ofprincipal stresses and the magnitude of greatest shear stresses.
At a point in a strained material, the intensities of normal stresses on two planes at right angles to each other are 35 N/mm2 and 20 N/ mm2 both tensile. They are accompanied by shear stress of 15 N/ mm2. Find the principal planes and principal stresses. Find also maximum shear stress.
At a certain section in a material under stress, direct stresses of 45 MN/m2 tensile and 75 MN/m2 tensile act on perpendicular planes together with a shear stress τ acting on these planes. If the maximum stress in the material is limited to 150 MN/m2 tensile, determine the value of τ.
you can provide handwritten solution also. At a point in a material under stress, the intensity of the resultant stress on a certain plane is 60 N/mm2 (tensile) inclined 30o to normal of that plane. The stress on a plane at right angle to this has a normal tensile component ofintensity 40 N/mm2.Using the Mohr’s circle calculate, resultant stress on the second plane, the principal planes and stress, plane of maximum shear and its intensity.
Can you help me with this problem, please: At a material point in plane stress it is known that the hydrostatic component of the stress is 15 ksi and that the second stress invariant is 30 ksi. Determine the magnitude of the principal stresses and the maximum shear stress.
At a point in a piece of elastic material there are three mutually perpendicular planes on which the stresses are as follows : tensile stress 50 N/mm2, shear stress 40 N/mm2 on plane, compressive stress 35 N/mm2 and complementary shear stress 40 N/mm2 on the second plane, no stress on the third plane. Find (a) the principal stresses and the positions of the plane on which they act (b) the position of the planes on which there is no normal stress.
a) Prime planes,b) Prime stresses, c) Maximum shear stress and thisin the plane of the stressdetermine the normal stress
2. The Principal stresses at a point across two perpendicular planes are 90MN/m² (tensile) and 40MN/m² (compressive). The shear stress across these planes is 25 MN/m² (counter clockwise). Find the normal, tangential and the resultant stress & its inclination on a plane making an angle of 35° with the plane of first stress.
The stresses at a point in a bar are 200 N/mm2 (tensile) and 80 N/mm2 (compressive). Determine the resultant stress in magnitude and direction on a plane inclined at 60° to the axis of the major stress. Also determine the maximum intensity of shear stress in the material at the point.