The problem with making a standard solution of sodium hydroxide from solid NaOH is that O a. the solid is hygroscopic and strongly absorbs water because of hydrogen bonding. O b. once the sodium hydroxide is made, carbon dioxides from the atmosphere immediately begins to react with the solution thereby changing its concentration. O the solid is extremely reactive and corrodes most laboratory containers. O d. the solid is extremely caustic and difficult to handle.

The problem with making a standard solution of sodium hydroxide from solid NaOH is that O a. the solid is hygroscopic and strongly absorbs water because of hydrogen bonding. O b. once the sodium hydroxide is made, carbon dioxides from the atmosphere immediately begins to react with the solution thereby changing its concentration. O the solid is extremely reactive and corrodes most laboratory containers. O d. the solid is extremely caustic and difficult to handle.

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter16: Applications Of Neutralization Titrations

Section: Chapter Questions

Problem 16.3QAP

See similar textbooks

Similar questions

You are asked to prepare a solution of sodium sulfate decahydrate with a final concentration of 0.22 m. Make sure you use up 20.0 g of sodium sulfate decahydrate for this solution.
An 7.50 ml aliquot of a 125 ppm stock Red 40 dye solution was diluted to a final volume of 25.0 mL with deionized water. What is the concentration of the dilute Red 40 dye solution (in ppm)? 37.5 ppm is the answer. (please show me how to calculate)
What mass of BaCl2 is needed to dissolve in 1.2 kg water to prepare 0.500m BaCl2 solution?
1.00 mL of a 3.55x10^-4 M solution of oleic acid is diluted with 9.00 mL of petroleum ether, forming solution A. Then 2.00 mL of solution A is diluted with 8.00 mL of petroleum ether, forming solution B. What is the concentration of solution B?
Prepare the following solution quantitatively using boiled distilled water 1. 250.0 mL 1.0 M stock HCl solutionNOTE: Use the 3.0 M HCl solution from the pic Prepare the following solution quantitatively using boiled distilled water 1. 250.0 mL 0.0500 M standard HCl solution from 1.0 M HClpls compute how to prepare them
Describe exactly how to prepare a series of 8 solutions of a reagent with dilution factor of 2 within the series and the most concentrated solution with concentration of c1 = 50.0 mM. Each solution within the series should be at least 20mL in volume.
you want to neutralize 24.1 mol of sulfuric acid with 5.34 M sodium hyrdoxide how many L of that hydroxide solution must you add to react exactly with the sulfuric acid?
Can you please solve question 2 on the attached document; showing step by step solution. Thank you
The following reaction is the basis for automatized breath tests for the detection of alcohol(e.g. the Breathalyzer):C2H6O + Cr2O72- --> C2H4O2 + Cr3+ The Cr2O72- ions generate a reddish orange aqueous solution that changes to green as Cr3+ ions are produced due to the reaction with ethanol (C2H6O). If the concentration of the dichromate (Cr2O72-) solution is 0.5 M, theconcentration of Cr3+ is 0.1 M, the concentration of ethanol in the solution is1x10-4 M and the concentration of acetic acid (C2H4O2) is 1×10-4 M calculate the value of Ecell for this reaction at 298 K. The value of E0cell is 1.27 V.
A 0.8M NaOH solution is diluted to a final volume of 500 ml and a finalconcentration of 0.2M. Calculate the amount of water used to dilute thestock 0.8M NaOH for this to happen.
What should be the volume of concentrated ammonium hydroxide that should be measured to prepare 100 mL of solution with a concentration of 0.2 mol/L? (Data: T = 29%; d = 0.88 g/cm³; MM = 35.04 g/mol).
0.54 g phthalic acid fully dissolve in 100 ml water at room temperature. How much is phthalic acid dissolves in the amount of water you used as part of this experiment?