The pump shown in the figure below delivers a head of 200 ft to the water. Determine the power that the pump adds to the water. The difference in elevation of the two ponds is 150 ft. Assume L = 300 ft, D = 0.75 ft. Ws = K₁ IN i Pump = 5.0 Kent=0.8 = 1.5 Pipe length = L Pipe diameter = D Pipe roughness = 0 ft-lb/s or IN K₁ i <= 1.0 Lexit hp

The pump shown in the figure below delivers a head of 200 ft to the water. Determine the power that the pump adds to the water. The difference in elevation of the two ponds is 150 ft. Assume L = 300 ft, D = 0.75 ft. Ws = K₁ IN i Pump = 5.0 Kent=0.8 = 1.5 Pipe length = L Pipe diameter = D Pipe roughness = 0 ft-lb/s or IN K₁ i <= 1.0 Lexit hp

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Show the necessary figures (if applicable) 2.3) Points A and B are separated by 915 m of new 152.4 mm diameter cast iron pipe. 50 lps of water flow from point A to point B. Point B is 18.5 m above point A. What must be the pressure at point A if the pressure at point B is 345 kPag and the head loss between A and B is 54 m? 2.4) A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm. If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
Try making the flow net for the following diagram. Given: H1= 6m H2= 1.5 m D= 8m D1= 4m Draw a flow net
Three reservoirs are connected by individual pipes to junction O as shown on the figure below. Find the elevation of reservoir C in order that the discharge in pipe AO from reservoir A is 0.15 cubic meter per second. Use Darcy-Weisbach formula with f = 0.02. Draw the final hydraulic gradient line (HGL). Reservoir Discharge, Q (m^3/s) Diam., D (cm) Length, L (km) WS elev. (m) A 0.15 (out) 35 1.40 145 B ? 25 0.90 125 C ? 30 1.60 ?
2] A pipe discharges 130 lps of water into a reservoir at a point 1.85 m belowthe water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25m above the water surface. At the discharge end the pipe is 30.5 cm. If the head lossfrom A to the reservoir is 0.7 m, determine the pressure in A.
Water of temperature 30o is flowing with flow rate 0.055 liters/s in a straight 50mm diameter uPVC pipe of length 450. Determine the head loss for this length by using Darcy Weisbach formula, and Hazen-William's formula.
A) what is the number of drop of the flownet? B) What is the flow of water in the unit of cm^2/min? C) What is the water pressure, u, at point A? (Assume the water unit is 10 kN/m^3) D) What is the total head at point B/ E) What is the water pressure at point B? (Assume the water unit is 10 kN/m^3)
Given the following information about a length of pipe: P1 = 440 kPa V1 = 0.0085 m/s z1 = 5 m v2 = 0.8335 m/s z2 = 0 m Head loss from point 1 to 2 = 0.262 m Find the pressure at point 2
A trapezoidal flume in the shape of a half-hexagonal has a base width of 1.5 m. It is laid at a slope "s", has a roughness coefficient "n" and the discharge is 3 cum/sec when flowing full. If the same material were used for the most efficient rectangular section . by how much would be the discharge decrease in cu.m/ sec? Use 2-decimal places What is the computed constant in (S^(1/2))/n? Use 3-decimal places What is the computed area of the rectangular channel/ Use 3-decimal places
1. A pipe has a slope of 1 in 100 and its length is 300 meters. Its diameter is 0.6 meter at the lower end while 1.2 meters at the higher end. The rate of flow through pipe is 5400 liters/min. Find the pressure at the lower end if the pressure at higher end is 68.07 kPa. Neglect losses.
Reservoir A has an elevation of 100 m. A pipe is connected from Reservoir A to Reservoir B. It has a length of 1000 m. and diameter of 600 mm. A pump is installed near Reservoir A and has a rating of 500 hp. If C = 110, rate flow is 550 L/s, 1. Determine the headloss in meters in the pipe. (ANSWER: 7.107) 2. Determine the head supplied by the pump in meters. (ANSWER: 69.132) 3. Compute the max elevation in meters of Reservoir B that pump could supply. (ANSWER : 162.025)
Two reservoirs are connected by three pipes. laid in parallel. The pipes diameters are respectively 10cm, 20cm and 30cm and they are of the some length. If discharge through 10cm pipe is 0.1 m3/s, calculate the discharge through the larger pipes. Assume the friction coefficient ‘f’ to be same for the pipes.
An open tank has a 3 m square horizontal section and weighs 3.5 kN. It contains water to a depth of 1.0 m. An unbalanced force of 15 kN is applied to the tank parallel to one of the pair of sides. Determine the minmimum height in meters of the tank in order to prevent any spillage. a.1.24 b.1.60 c.1.76 d.1.50