The rated speed of drum B of the belt sander shown in Figure 4 is 2400 rpm. When the power is turned off, it is observed that the sander coasts from its rated speed to rest in 10 s. Assuming uniformly decelerated motion, determine the velocity and acceleration of point C of the belt, (a) immediately before the power is turned off, (b) 9 s later. 25 mm C 25 mm Figure 4

The rated speed of drum B of the belt sander shown in Figure 4 is 2400 rpm. When the power is turned off, it is observed that the sander coasts from its rated speed to rest in 10 s. Assuming uniformly decelerated motion, determine the velocity and acceleration of point C of the belt, (a) immediately before the power is turned off, (b) 9 s later. 25 mm C 25 mm Figure 4

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The mechanism shown is used in a distribution center to push boxes along a platform. The input link is driven by an electric motor which, at the instant shown, has a speed of 25 rad./s and accelerates up to 500 rad./s2. If the input link is 250 mm long and forms a 40 degree angle with the horizontal, determine the instantaneous acceleration of the input link end at the position shown (Point A).
The rated speed of drum B of the belt sander shown is 2400 rpm. When the power is turned off, it is observed that the sander coasts from its rated speed to rest in 10 s. Assuming uniformly decelerated motion, determine the velocity and acceleration of point C of the belt, (a) immediately before the power is turned off, (b) 9 s later.
A small grinding wheel is attached to the shaft of an electric motor which has a rated speed of 3600 rpm. When the power is turned on, the unit reaches its rated speed in 5 s, and when the power is turned off, the unit coasts to rest in 70 s. Assuming uniformly accelerated motion, determine the number of revolutions that the motor executes (a) in reaching its rated speed, (b) in coasting to rest.
how are the radial accelerations of points at the teeth of the two sprockets related? Explain.
The rotor of a gas turbine is rotating of 12 rad/s when the turbine is shut down. It is observed that 4 min is required for the rotor to coast to rest. Assuming uniformly accelerated motion, determine the number of revolutions that the rotor executes before coming to rest
Hi, I need help with this question please. Block A is connected to a fixed pin O with a string 100 mm long. The block and the channel are at rest when a motor on a shaft through O starts to rotate the channel with angular velocity ω = sin(0.2t) rad/s and the string starts to pull the block towards O with speed v = sin(0.2t) mm/s. 1. At the time instant t = 2.5π s, determine: a) the components of the velocity and acceleration of the ball in polar coordinatesb) the speed of the ballc) the components of the velocity and acceleration of the ball in normal coordinatesd) sketch the polar and normal components of the velocity and acceleration of the ball on the figure.
In the cam-follower mechanism shown, the slotted bar rotates with constant angular velocity ω = 10 rad/s and the radial position of follower A is determined by the cam profile at rest. The tracker path can be described by the polar equationr = 1 + 0.5 cos 2θ ft.Determine the acceleration of the cam follower when θ = 30° a) in terms of polar coordinates and b) in terms of Cartesian coordinates.
The relative acceleration of point A with respect to point B of the disk in Figure 1 is given asaA/B = 3.347i + 1.283j. If the disk rolls without slipping, determine the angular velocity andangular acceleration of the disk at the instant. If, in other case, the disk rolls with slipping andthe vM = 2 m/s to the left and vO = 2 m/s to the right, do you think that the process ofdetermining its angular velocity and angular acceleration becomes easier or harder?
From rest, the motor shaft I rotates to achieve a counter-clockwise angular velocity, ?? = (0.13?3 +3.32?2) rad/s. If no slippage occurs within the system and considering the tabulated given below, determine the velocity and total acceleration of the point 0.3 meter from the center of Disk E, as shown, at ? = 1.22000 second. Also, determine the number of revolutions done by Disk E at the same time.
The power of an engine running at 125 rpm is turned off and the engine comes to rest at the end of 2 min and 40 sec. Assuming that there is no slipping between the belt and pulley surface and that the deceleration is uniform, find 1) the average speed in radians per second of the engine pulley in coming to rest; 2) the total angular distance traveled in revolutions, radians and degrees in coming to rest; 3) the distance in feet traveled by a belt running on the pulley in coming to rest, if the pulley diameter is 3ft.
Figure 7.7 shows a power hacksaw. At this instant, the electric motor rotates counterclockwise and drives the freeend of the motor crank (point B) at a velocity of 12 in./s. Additionally, the crank is accelerating at a rate of 37 rad/s^2. The top portion of the hacksaw is moving toward the left with a velocity of 9.8 in./s and is accelerating at a rate of 82 in./s^2. Determine the relative acceleration of point C with respect to point B.
B. In Fig. below; rod AB rotates about an axis through A and is connected to block D by a flexible and inextensible cable. Determine the linear velocity of block D when 0 = tan ( 3 /4 ), and the angular velocity of AB is 2.5 rad / sec counterclockwise. Fig.2.B B 1.5m 25m