The rectangular piece of wood, 72 mm by 193 mm, is used as a compression block. The grain of the wood makes a 16.3° angle with the horizontal, as shown in the figure. Determine the shearing stress (in MPa) on the plane of the grain if the allowable compression stress on the plane of the grain is 28.5 MPa. Round off the final answer to four decimal places.

The rectangular piece of wood, 72 mm by 193 mm, is used as a compression block. The grain of the wood makes a 16.3° angle with the horizontal, as shown in the figure. Determine the shearing stress (in MPa) on the plane of the grain if the allowable compression stress on the plane of the grain is 28.5 MPa. Round off the final answer to four decimal places.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The steel shaft with two different diameters rotates at 4.4 Hz. The power supplied to gear C is 73 kW, of which 48 kW is removed by gear B. Find the maximum shear stress (in Pa) in the shaft if d = 59 mm, h = 61.7 mm, L = 3.9 m, M = 2.5 m, and G = 83.34 Gpa. Round off the final answer to two decimal places.
For the direct shear example shown below, if F = 47 kN, AAB = ACD = 3151 mm2, the average shear stress in the internal vertical surface AB (or CD), = ______ MPa. Calculate your answer to 1 decimal place.
The rectangular piece of wood, 84 mm by 180 mm, is used as a compression block. The grain of the wood makes a 21.2º angle with the horizontal, as shown in the figure. Determine the largest axial force P (in N) that can be applied safely if the allowable stresses on the plane of the grain is 16.4 MPa for compression. Round off the final answer to three decimal places.
The cross-section of bar ABCD is made of a triangle with sides equal to 15 mm, 12 mm, and 10 mm. Determine the maximum normal stress in the bar. Express o in MPa and round off your answer in 2 decimal places. Please answer this one
1. Determine the orientation of the planes of maximum in-plane shearing stress using Mohr's circle. The orientations of the planes of maximum in-plane shearing stress are −____ °and ____°. 2. Determine the maximum in-plane shearing stress using Mohr's circle. The maximum in-plane shearing stress is ___ksi 3. Determine the normal stress using Mohr's circle. The normal stress is___ ksi.
The cylinder of a hydraulic press is made up of thick-walled cylinder having an inside diameter of 300 mm. It is subjected to an internal pressure of 40 MPa Determine the thickness of the cylinder without exceeding a shearing stress of 80 MPa. A. 109.81 mm C. 95.56 mm B. 75 mm D. 120.71 mm
The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.6-in .-diameter pin at A, and the 0.32-in .-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5351 lb. Round off the final answer to two decimal places.
The wooden members' A and B are to be joined by plywood splice plates that will be fully glued on the surfaces in contact. The clearance between the ends of the members is to be 13.5 mm, the length of the plywood is L = 246 mm and the width of the wood is W = 133 mm. Find the largest possible value of P (in N) if the average shearing stress in the glue is not to exceed S = 872 kPa. Round off the final answer to three decimal places.
At a certain section in a material under stress, direct stresses of 45 MN/m2 tensile and 75 MN/m2 tensile act on perpendicular planes together with a shear stress τ acting on these planes. If the maximum stress in the material is limited to 150 MN/m2 tensile, determine the value of τ.
A hollow steel shaft, 5.6 ft long, has an outer diameter of 3.02 in. and an inner diameter of 1.5 in. The shaft is transmitting 166 hp at 108 rev/min. Determine the maximum shear stress (in psi) in the shaft. Round off the final answer to two decimal places.
Mohr's Circle At a point, the normal and shear stresses acting on one plane are 8000 psf compression and 2000 psf, respectively. On a perpendicular plane, the normal and shear stress combination is 2000 psf compression and 2000 psf. (a) Draw the Mohr's circle. (b) Determine the value of the principal stresses. (c) Find the angle between the plane on which the 8000 psf compressive stress acts and the major principal plane. (d) What is the maximum shear stress acting at the point? kindly answer the following with a complete solution so that i can understand how to solve it. thank you
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 16.8 mm. Determine the largest allowable value of P (in N) if the shear stress in the shaft is not to exceed 88.86 MPa and its angle of twist is limited to 5.15˚. Use G = 80.77 GPa for steel and L = 462 mm. Round off the final answer to two decimal places.