The rectangular plate is subjected to the deformation shown by the dashed lines. Determine the- followings: 1) the average normal strain along side AB 2) the average normal strain along the diagonal AC 3) the average normal strain along the diagonal BD 4) the shear strain at B 5) the shear strain at D y

The rectangular plate is subjected to the deformation shown by the dashed lines. Determine the- followings: 1) the average normal strain along side AB 2) the average normal strain along the diagonal AC 3) the average normal strain along the diagonal BD 4) the shear strain at B 5) the shear strain at D y

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15o with the x-axis. What is the tensile stress of section AA’? Determine the shear stress on plane AA’ At what angle of plane AA’ is the shear maximum.
The geometry of the PQR plate after deformation (PQ'R) is shown with dotted lines. Calculate the shear unit strain at the Q 'corner.
A uniform steel shaft has a diameter of 50 mm is fixed at ends A and B. The shear modulus of steel is 75 GPa.d) Calculate the maximum shear stress in the system in MPa. You will have to look at each individual piece of the system, so clearly indicate which segment has the maximum stress.[Ans. to check: τmax = 8.15 MPa]e) Calculate the total rotation of the shaft at point C in radians.
The rectangular plate undergoes a deformation shown by the dashed lines. Determine the shear strain gxy and gx′y′ at point A.
The strain components for a point in a body subjected to plane strain are Ex - 930 JE, Ey - -112Que and Wxy - -583 urad. Using Mohr'scircle. determine the principal strains (6p1 > p2), the maximum inplane shear strain yip, and the absolute maximum shear strain Ymax atthe point. Show the angle , (counterclockwise is positive, clockwise is negative), the principal strain deformations, and the maximumin-plane shear strain distortion in a sketch.
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 1.4 mm and upward by v = 3.5 mm to new position Q′. Determine the shear strain γ at corner Q′ after deformation. Use c = 755 mm, α = 33°, and β = 57°.
NO. 3 Given the beam shown with computed reactions and a cross section. Determine the maximum tensile stress of the section.
Three strain gauges are attached on the surface of the plane frame which is shown in Figure. The angle between each strain gauges are θº=69º. Reading from these gauges are: εa= 1100 μ, εb =305 μ and εc = -240 μCalculate:(a) The principal strains(b) The maximum shear strain
The deformation on the given plate is shown with dotted lines. Calculate the shear unit strain at corners A and B.
A hollow steel shaft with an outside diameter of 67 mm and a wall thickness of 11 mm is subjected to a pure torque of T = 5100 N-m. The shear modulus of the steel is G = 82 GPa. Determine:(a) the maximum shear stress τ in the shaft.(b) the magnitude of the angle of twist φ in a 2.4-m length of shaft.
For the beam and loading shown, consider the n-n cross section. (a) the absolute value of |M| of the bending moment in the n-n section N.m (b) determine the absolute value of the normal stress in the direction of the X axis at point A of the n-n section |σx| MPa in units, c) determine the absolute value of the maximum shear stress at Point A of the n-n section |tmaks| MPa in units. The inside of the beam is full and the cross-section measures are as shown in the figure. Supports only support vertical forces. Take P1 in the question for 220 N and P2 for 323 N. Point A is at the bottom of the beam.
The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 9 kN, determine the magnitudes of the average normal stress in the shank, the average shear stress along the cylindrical area of the plate defined by the section lines a–a,and the average shear stress in the bolt head along the cylindrical area defined by the section lines b–b. Answers should be in MPa.