The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 20 mm² and is made from 6061-T6 aluminum. (Figure 1) Figure 1.5 m 2 m 300 N/m 2 m 1 of 1 Part A Determine the vertical deflection of the bar at D when the distributed load is applied. Express your answer to three significant figures and include the appropriate units. 8p=17.3 μÃ mm Submit Previous Answers Request Answer Provide Feedback ? * Incorrect; Try Again; 5 attempts remaining

The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 20 mm² and is made from 6061-T6 aluminum. (Figure 1) Figure 1.5 m 2 m 300 N/m 2 m 1 of 1 Part A Determine the vertical deflection of the bar at D when the distributed load is applied. Express your answer to three significant figures and include the appropriate units. 8p=17.3 μÃ mm Submit Previous Answers Request Answer Provide Feedback ? * Incorrect; Try Again; 5 attempts remaining

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel bar with a thickness 5 mm is to carry a load of 2000 N. Using the direct method,determine the deflection at each node and the average stress in each part. Divide the bar into three parts. (E=200 GPa)
A hollow shaft with outside diameter of 14 cm and wall thickness of 0.8 cm transmits 400 KW at 400 rpm. What must be the angular deflection if the length is 5 m? G= 12 Mpsi
To use deformation compatibility equations to calculate loads and deflections for statically indeterminate axially loaded columns. As shown, two composite columns of steel and concrete are used to support a rigid platform. The columns are cylindrical, with a steel bar encased in concrete. The outer diameter of each column is dc = 26 cm . The steel in the left column has a diameter of d1 = 13 cm . A load of P = 56 kN is applied with L1 = 1.8 m and L2 = 1.9 m . The height of the columns is h = 2.2 m . The moduli of elasticity for steel and concrete are Es = 200 GPa and Ec = 30 GPa , respectively.
A hollow steel [E= 30,000 ksi] tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum [E= 10,000 ksi] rod (2) that has a 2-in.-diameter and a solid 1.375-in.-diameter aluminum rod (3). Determine: (a) the change in length of steel tube (1).(b) the deflection of joint D with respect to the fixed support at A.(c) the maximum normal stress in the entire axial assembly.
The ply stress σα was calculated for AS1/3501-6 Graphite/Epoxy laminates [0/+-45]s under load with N1=10,000 N/m and N2=N6=0. When the strength of this material is as follows, determine the stability of the laminate according to the maximum stress theory.
A steel [E = 200 GPa] rod with a circular cross section is 13-m long. Determine the minimum diameter D required if the rod must transmit a tensile force of 23 kN without stretching more than 4 mm. 13.18 mm 28.25 mm 20.13 mm 25.90 mm 21.81 mm
The wires each have a diameter of 2 cm, length of 6 m, and aremade from a material with modulus of elasticity ? = 19.3 GPa.If three external loadings are applied to the rigid beam AC,determine the angle of tilt of the rigid beam. Assume thedeformation of the wires obeys the Hooke’s law
A large water tank that has a capacity to carry 20,000 liters is to be supported by four cylindrical posts. These four support posts are made of plain carbon (1045) steels with the yield and tensile strengths of 310 MPa and 565 MPa, respectively. Determine the minimum required diameter of the post assuming a factor of safety of 5.
Determine the elongation of an aluminium hollow cylinder of an inner diameter of 1.45 cm & the external diameter of 24.7 mm is subjected to an elastic tensile load of 251 kN. Take the elastic modulus of the aluminum specimen as 71 GPa and the initial length of the hollow cylinder as 198 mm. Solution: Cross-sectional Area (in mm2) = Stress-induced (in N/mm2) = Strain-induced (at least 3 decimal places accuracy)= Elongation (in mm) =
A wire 20 m long, weighing 0.8 N per m, and having a cross sectional area of 6.2 mm^2, is suspended vertically from its upper end, E = 103 GPa. Calculate the total elongation if a load of 220 N is attached to its lower end. A)9.22mm B)7.39mm C)6.89mm D)8.42mm
The circular section steel bar bent in L shape is attached to a fixed wall at end A. A force P is applied to the rod in the vertical direction from the free end C. In what range is the safe diameter value of this ductile rod according to Von-Mises criterion? P=3kN, L1=3m, L2=2m, sak= 400MPa, tak= 200MPa, safety factor : n = 2 p = 3
2.15 A single axial load of magnitude P = 58 kN is applied at end C of the brass rod ABC. Knowing that E = 105 GPa, determine the diam- eter d of portion BC for which the deflection of point C will be 3 mm. 30 mm 1.2 m Fig. P2.15 B -0.8 m Note:- • Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. • Answer completely. • You will get up vote for sure.