The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminum and bronze. Determine the vertical displacement of the point where the force P = 10 kips is applied. Neglect the weights of the members. Aluminum L= 3 ft A = 0.75 in.2 E = 10 x 10 psi A ৩) B Bronze L =4 ft A =0.25 in.2 E = 12 x 10 psi 2 ft-i-2 ft

The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminum and bronze. Determine the vertical displacement of the point where the force P = 10 kips is applied. Neglect the weights of the members. Aluminum L= 3 ft A = 0.75 in.2 E = 10 x 10 psi A ৩) B Bronze L =4 ft A =0.25 in.2 E = 12 x 10 psi 2 ft-i-2 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bars AB and CD are supported by pins atA and D. The vertical rods are made of aluminumand bronze. Determine the vertical displacement ofthe point where the force P = 10 kips is applied.Neglect the weights of the members.
Determine the force in member BA (in lb, round-off to 2 decimal places, include "-" if compression) of the scissors truss shown. P = 150.0 lb, Q = 75.0 lb, and L = 10.0 ft.
7. Determine the magnitude of the force in memberBD and BE. (lb)
The rigid bars AB and CD are supported by pins at A and D. The verticalrods are made of aluminum and bronze. Determine the vertical displacement of the point where the force P=10 kips is applied. Neglect the weights of the members.
Two members AB and AC are made of material with E= 91 Gpa and each member has cross sectional area of A= 290 mm2. The members are used to support bar BC. If P=2079 N, L1= 202 mm , L2= 313 mm and L3= 480 mm . Answer the following questions. The tension in member AB The tension in member CD The elongation in member AB The elongation in member CD Vertical displacement of point E
The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminum and bronze. Determine the vertical displacement of the point where the force P =10 kips is applied. Neglect the weights of the members.
Determine the forces in members BC BE, and CE of the truss shown. The length of all members is 3 meters
The steel bars AC and BC, each of cross-sectional area 120 mm2, are joined at C with a Determine the displacement of point C caused by the 15-kN load. Use E = 200 GPa for steel.
Each steel member has a cross sectional area of 300 sqmm. Determine the force on member AC. Determine the horizontal and vertical displacement at B.
A tripod shown supports a load of P = 1000 N at point A. Take note that ball and socket joints are used to mount the triopd at points B, D, and C. Consider the following:L1 = 2L2 = 4L3 = 5θ = 45°α = 30 Point C coordinates: (2, -2, 3) *Do not use Vectors in solving Determine the following: Force of AB = __NForce of AC = __NForce of AD = __N
The timber member BC, inclined at angle Θ=60 degrees to the vertical, is supported by a pin at B and the 0.75in. diameter steel bar AC.(a) Determine the cross-sectional area of BC for which the displacement of C will be vertical when 5000lb force is applied.(b) Compute the corresponding displacement of C.The moduli of elasticity are 1.8 x 106 psi for timber and 29 x 106 psi for steel. Neglect the weight of BC.
The steel bars AC and BC, each of cross-sectional area 120 mm2, are joined at C with a pin. Determine the displacement of point C caused by the 15-kN load. Use E = 200 GPa for steel.