The rod ABCD is made of an aluminum for which E= 70 GPa. Take P= 90 kN. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A 1.75 m Area = 800 mm² B 1.25 m C Area = 500 mm2 75 kN 1.5 m 50 kN

The rod ABCD is made of an aluminum for which E= 70 GPa. Take P= 90 kN. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A 1.75 m Area = 800 mm² B 1.25 m C Area = 500 mm2 75 kN 1.5 m 50 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.1P: The rails of a railroad track are welded together at their ends (to form continuous rails and thus...

See similar textbooks

Related questions

Q: 2- Determine the total deformation between points A and D of a stepped steel bar subjected to the…

Q: A steel bar with length of 4.5 m is subjected to forces as shown in the figure: 1. Determine the…

Q: Consider the truss structure with a load of P= 35.4 kN applied at joint C. All the members of the…

Q: Four axial forces are applied to the 25mm thick structural steel bar with 40mm diameter pins as…

A: for solution refer below images,

Q: A solid steel post having a length of 3m and a diameter of 80 mm is subjected to pure torsion. a)…

A: Answer: (a) The torsional rigidity of the steel post is 321.7 × 109 N•mm2. (b) The torsional…

Q: The allowable tensile stress for wires AB and AC is ơallow = 210 MPa, and wire AB has a diameter of…

A: Given data:-Allowable stress in wire AB & AC=σABallow=σACallow=210MPadiameter of wire AB,…

Q: The aluminum bar with cross-sectional area of 160 mm2 carries the axial loads at the position shown…

Q: The rod BD is made of material with G1= 137 GPa has a diameter 42 mm is bonded to the tube CA at…

Q: The rigid bar ABC and EFG are supported by pins at A and G. The vertical rods are made of steel (rod…

A: Given: The temperature change, Δt = 50o The coefficient of thermal expansion, α = 0.0000117/oC The…

Q: A gap of 0.02 in. exists between the composite rod and the wall when the temperature is 75°F. NOTE:…

Q: The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional…

Q: The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. 6ft AAn = 1 in Agg = 2…

Q: 1. A rod of length 1.50 m and diameter 0.12 m is mounted in a rigid wall A vertical bar of length…

A: INTRODUCTION : In order to solve the above problem, the maximum shear stress theory is applied when…

Q: Ropes J, K, and L with their ends attached to each other as shown supports a downward force Q=100N.…

Q: The assembly shown in Figure consists of an aluminum tube AB having a cross-sectional area of 400…

Q: The rods 1, 2, and 3 shown below are welded together, mounted between two rigid walls and subjected…

A: Given data as per question Length of rod 1 and 3 =1 m Length of rod 2 =1.8 m…

Q: Compute the total elongation caused by an axial load of 147 kN applied to a square bar, tapering…

Q: The rigid bar AB attached to aluminum and steel rods, is horizontal before the load P is applied.…

A: Aluminum: L= 3 m= 3000 mmA= 500 mm2E= 70 GPa= 70000 MPa Steel: L= 4 m= 4000 mmA= 300 mm2E= 200 GPa=…

Q: 7. The rigid slab which weighs 600 kN is supported by three rods of the same cross-section and…

Q: A steel [E = 25500 ksi] pipe column (1) with a cross-sectional area of A1 = 5.60 in.2 is connected…

Q: 6. The plastic sheet, 1/2 in. thick, is bonded to the pin-jointed steel frame. Determine the…

A: GIVEN DATA- G=70*10^3 psi Thickness t=1/2in we have to find value of force P

Q: A stepped circular bar having diameters of 20 mm, 15 mm, and 10 mm over axial lengths of 100 mm, 80…

Q: A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P =…

Q: The axial assembly consists of a solid 1.03-in.-diameter aluminum alloy [E = 9700 ksi, v = 0.24, a =…

Q: Let's consider a rod subjected to the shown axial forces. If we consider a lincar elastic behavior,…

A: Stress: Stress is nothing but the force per unit area. It is represented by σ. SI unit of stress is…

Q: A hollow circular column of internal diameter 20 mm and external diameter 40 mm has a total length…

A: giveninternal diameter of column d=20mmexternal diameter D=40mmtotal length L=5mE=2×105N/mm2yeild…

Q: A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P =…

Q: sectional area of Arod = 0.75 in². If a load of P = 24 kip is applied to the end of rod, determine…

Q: Q15. The rigid bar is supported by steel rods (E - 200,000 MPa) (AB, CD and EF) and hinge as shown…

Q: A column with rectangular cross section of breadth = 9mm and depth = 4mm, has its both ends are…

Q: A circular column is made of concrete [E. = 4.2(10³)ksi] while being reinforced with six steel rods…

A: I have attached my answer below, please refer and give me +ve rating, Thanks!

Q: Q For the assembly shown in the figure, brass rod AE (E=105 GPa) and aluminum rod BF (Ea=70 GPa)…

Q: Beam ABD supports an 80 kg vertical mass connected at point D. The beam has a pin connection at the…

Q: QUESTION 3: Square profile made of hollow 1045 steel, with a length of 6 meters with a…

A: Given data: Cross-section of Square hollow profile of steel pipe is drawn below. Cross-sectional…

Q: The rectangular bar is connected to the support bracket with a 24-mm-diameter pin. The bar width is…

Q: The cross-sectional area of the bar is 5 cm². Use E = 70 GPa for aluminum, and E = 200 GPa for…

Q: A copper bar consists from three sections: sections 1 is of 25 mm diameter and 60 mm long, section 2…

A: Calculate the cross-section area of section 1. A1=πd124 Here, d1 is the diameter of section 1, and…

Q: The cylindrical steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. The column…

A: GivenD=4ind=3.5inσwcolumn=27000psiσwconcrete=1300psi

Q: 4. A steel bar of 40 mm x 40 mm square cross section is subjected to an axial compressive load of…

Q: The prismatic bar has a cross-sectional area A = 3 in² and is made of material with modulus of…

A: Given: The cross-sectional area of bar is A=3 in2. The modulus of elasticity is E=28×106 psi. The…

Q: The rod BD is made of materia with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at…

Q: A steel [E = 59500 ksi] pipe column (1) with a cross-sectional area of A1 = 5.60 in.2 is connected…

A: Given: The modulus of elasticity of pipe 1, E1 = 59500 ksi The cross-section area of pipe 1, A1 =…

Q: A steel bar with diameter d1 = 10 mm has upset ends with diameter d2 = 15 mm. The lengths of the bar…

Q: QUESTION 3 Calculate for E=200 GPa: 3.1 The diameter 'd' if the stress is not to exceed 142 MPa 3.2…

A: As per given question we determine the value of D and x

Q: The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at…

A: Given data Diameter of rod BD = 16 mm Outer diameter of rod CA = 37 mm Thickness (t) = 7 mm

Q: L1 PB 2 E2 L2 D2 Dimensions: L2 L1 D2 D1 17 mm 18 cm 23 cm 15 mm Problem Statement: The rod shown is…

A: Consider the following diagram showing the forces (loads) acting on the system of two rods of…

Q: Q15. The rigid bar is supported by steel rods (E = 200,000 MPa) (AB, CD and EF) and hinge as shown…

Q: Rod A has a cross-sectional area of 2 in^2 and a modulus of elasticity of 10E6 psi. Rod B has a…

Q: I. A steel rod is acted upon by the loading shown below. 50 mm2 is the area of the circular rod. The…

A: Consider the Free body diagram: Force in segment AB, PAB=2 KNForce in segment BC, PBC=2+4 =6…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A metal block of cross-section area A and length L is subject to a tensile stress of S. The block elongates by a length of 0.002L. Another block made from the same metal is subject to the same tensile stress. If this block has a cross-section area of 2A and a length of 2L, determine the elongation of the block.
A metal block of cross-section area A and length L is subject to a tensile stress of S. The block elongates by a length of 0.001L. Another block made from the same metal is subject to the same tensile stress. If this block has a cross-section area of 2A and a length of L, determine the elongation of the block.
2. A bar of thickness 15mm and having a rectangular cross-section carries a load of 120kN. Determine the minimum width of the bar to limit the stress to 200MPa. The bar, which is 1m long, extends by 2.5mm when carrying a load of 120kN. Determine the modulus of elasticity of the material of the bar.
A steel bar AD has a cross sectional area of 300mm^2 and loaded by a force P1=15kN, P2=10kN, and P3=8kN. The lengths of the segments are a=2.0m, b=0.6m, and c=0.90m. E=200GPa. a. Determine the change in length of the bar. b. determine the stress of member BC. c. By what amount should the load P3 be incresed so that the bar does not change in length when the three loads are applied?
Two square bars (15mm thick) are bolted together as shown. Volt's allowable shear stress is 90 MPa, allowingCompression stress is 150 MPa.a) At this point, what is the minimum diameter of the bolt when the tensile force P=31 kN is applied?b) If the bolt is 20 mm in diameter, what is the maximum permissible load?
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure 1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (σY)st=680 MPa, and for the bronze (σY)br=490 MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa.
A seamless cylinder of storage capacity of 0.03m3 is subjected to an internal pressure of 21 MPa. The allowable stress in the material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.8mm A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.540mm
A stepped circular bar having diameters 20 mm, 15: mm and 10 mm over axial lengths of 100 mm, 80mm and 60mm is subjected to an axial tensile force of 5 KN. If E= 100 x 103 N/mm2 and 1/m = 0.32 for the material of bar, determine total change in length and change in each diameter.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm If the yield stress for the steel is (σY)st=610MPa, and for the bronze (σY)br=490MPa(, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa.
In a standard tensile test a steel rod of 7/8 in. in diameter is subjected to a tension force of 17 kips. Determine the ratio of the shear modulus to the modulus of elasticity of a material whose Poisson's ratio is 0.25.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure 1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (σY)st=680MPa, and for the bronze (σY)br=490MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa. Express your answer to three significant figures and include appropriate units.