IncorrectThe Scotch-yoke mechanism converts rotational motion of the disk to oscillatory translation of the shaft. Using the values e = 30°, w =5.4 rad/s, a = 2.1rad/s?,r = 230 mm, d = 610 mm, and ß = 16°, determine the velocity and acceleration of point P of the shaft. Thevelocity and accelerations are positive if to the right, negative if to the left.Answers:Vp =-0,563m/sap =i -6.195m/s?

Answered: Image /qna-images/answer/d35df363-f589-4010-89fe-7a1c5b3679d6.jpg

The Scotch-yoke mechanism converts rotational motion of the disk to oscillatory translation of the shaft. Using the values e = 30°, w = 5.4 rad/s, a = 2.1rad/s², r = 230 mm, d = 610 mm, and B = 16°, determine the velocity and acceleration of point P of the shaft. The velocity and accelerations are positive if to the right, negative if to the left.

The Scotch-yoke mechanism converts rotational motion of the disk to oscillatory translation of the shaft. Using the values e = 30°, w = 5.4 rad/s, a = 2.1rad/s², r = 230 mm, d = 610 mm, and B = 16°, determine the velocity and acceleration of point P of the shaft. The velocity and accelerations are positive if to the right, negative if to the left.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cyclist pedals constantly at 7.9587 rad/s the wheels are 336.5mm in radius. If the chain is directly connected with the sprockets which are 76 mm in radius (front sprocket) and 35mm in radius (rear sprockets), Determine the angular speed of the wheel in rad/s.
b) Find the angular velocity and angular acceleration of disc B shown below, which is spinningatthe constant rate of ω2 = 90/πrpm. The disc is attached to collar A, which is rotating at the angular speed of ω1 = 5/π rpm, with the angular speed increasing at 0.5/π rpm/sec. Rod AB which connects the disc to the collar ispinned to the collar at A. The rod makes an angle of θ = 300 with the vertical, which is increasing at a constant rate of20/π0/sec.Express theAngularvelocityAcceleration of the disc in terms of a reference frame attached to thecollar.
The disk with radius r = 0.09 m is rotating at a constant angular velocity of ω = 0.9 rad/s (counterclockwise) about the fixed pin support at O. For the instant shown, find the relative acceleration component (aB/A)n, where (aB/A)n = {(ax)i+(ay)j} m/s2. Choose the correct answer: a) ax=-0.292; ay=-0.0729 b) ax=0.786; ay=0.196 c) ax=0.292; ay=0.0729 d) ax=0.0182; ay=0.00349 e) ax=-0.786; ay=-0.196
In the figure, the wheel rolls with no slippage at the angular velocity shown. Based on the IC of the system as shown, determine: a. The angular velocity of bar AB with respect to time b. The speed of the slider at B
The constant angular acceleration of the rotating disk is 12 rad/s . The angular velocity of the disk is 24 rad/s clockwise when t = 0. Determine the total angle turned by the disk between t = 0 and t = 4sec. the answer is 48 rad. show your solution.
find an acceleration of the center of the beam (marked as a blue point) which is connecting both wheels , if it is known that linear velocity ot the wheels v=100km/h, r=0,8m and the distance drom the center of the wheel and the pont where the beam is connected (marked as red red distance)=0,4m, there is no slipping between wheels and the ground
Q2. The peg Pis driven by the sotted link whose motion is defined by theta= 1.5t and r = 0.8theta2. Find Determine the radial and transverse components of velocity and acceleration of the peg P after 1 sec time.
Disk B is at rest when it is brought into contact with disk A, which is rotating freely at 450 rpm clockwise. After 6 seconds of slippage, during which each disk has a constant angular acceleration, disk A reaches a final angular velocity of 140 rpm clockwise Disk radius a =3 in Disk radius b= 5 in. Determine the final linear speed at the point of contact between the disk in in/s
DO NOT INCORPORATE I-J-K IN THE SOLUTION!!! Gear A is between a stationary gear rack F and the gear rack E, which imoving at VE = 6 ft/s to the right at the instant shown. It is also observed that the acceleration of gear A is 2 ft/s2 also to the right. At this same instant, determine the angular velocity and angular acceleration of disk B. Use RMA for velocity analysis.
Consider the portion of an excavator shown. At the instant under consideration, the hydraulic cylinder is extending at a rate of 5 in./sec, which is decreasing at the rate of 2 in./sec every second. Simultaneously, the cylinder is rotating about a horizontal axis through O at a constant rate of 13 deg/sec. Determine the velocity v and acceleration a of the clevis attachment at B. Determine the r- and θ-components of velocity and acceleration. Answers: vr = in./sec vθ = in./sec ar = in./sec2 aθ = in./sec2
In the figure shown, the hydraulic cylinder moves upwards with a constant speed of Va=0.2 m/s, transferring vertical movement to corner A of the container. If bearing b never slips and has a diameter of 8 cm, determine the angular velocity of the imaginary line drawn from its axis of rotation to any point on its periphery. Determine the angular velocity of side CD at this moment.
Consider the portion of an excavator shown. At the instant under consideration, the hydraulic cylinder is extending at a rate of 7 in./sec, which is decreasing at the rate of 3 in./sec every second. Simultaneously, the cylinder is rotating about a horizontal axis through O at a constant rate of 10 deg/sec. Determine the velocity v and acceleration a of the clevis attachment at B. Answer the blank questions only