Answered: The semi-circular gate shown in the…

Name: Hydraulics The semi-circular gate shownin the figure is hinged at B.De
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Hydraulics The semi-circular gate shownin the figure is hinged at B.Determine the force Prequired to hold the gate inposition.waterPhingeB1.8 m1.2m

Engineering

Mechanical Engineering

The semi-circular gate shown in the figure is hinged at B. Determine the force P required to hold the gate in position. water P hinge B 1.8 m 1.2 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
Determine the magnitude of the force on the inclined gate 1.5m by 0.5m shown in the figure. The tank of water is completely closed and the pressure gage at the bottom of the tank reads 90,000 N/m2. Use 9800 N/cubic meter for water? Ans: 48022.5N
The contractor ran out of gunite mixture and fi nished thedeep corner of a 5-m-wide swimming pool with a quartercirclepiece of PVC pipe, labeled AB in Fig. .Compute the horizontal and vertical water forces on thecurved panel AB .
Show the derivation of the girth and longitudinalstresses of the thin-walled cylindrical container shownbelow. Say p is the internal pressure, d is the insidediameter of the container, and t is wall thickness.
A hydraulic lift is to be used to lift a 5000-lb weight by putting a weight of 50 lb on a piston with a diameter of 0.50 ft. Determine the diameter of the piston on which the weight is to be placed.
vessel a, at elevation 2.438m, contains water under 103.4 kpa pressure. Vessel B at elevation 3.658 m, contains a liquid under 68.95 kpa pressure. if the deflection of the differential gage is 305 mm of mercury, with the lower level on the A side at elevation 0.305m, determine the specific gravity of the liquid in vessel B. Ans. 0.500
An open rectangular tank 1 m wide and 2 m long contains gasoline to a depth of 1 m. If the height of the tank sides is 1.5 m, and if it slides down a frictionless plane that is inclined at 300 with the horizontal, determine the angle the free surface makes with the horizontal. Ans. The free surface is the same as the angle.
A thin-walled hollow sphere 3.8 m in diameter holds helium gas at 1767 kPa. Determine the minimum wall thickness of the sphere in mm if its allowable stress is 84.8 MPa.
Find the height of the portion of a cubic block that extends below the water surface (h) , the specific gravities of block and seawater are given to be SG = 0.778 and 1.025, respectively. h1 = 13.1cm
A 2.4-m-diameter, 3-m high, open cylindrical steel tank contains 2.1 m deep of water. Determine the stress, in MPa, in the walls of the tank near the bottom if the wall thickness is 8 mm. Note: Give me right solution with clear calculations.
A 4-ft diameter spherical tank is subjected to an internal pressure of 12 psf. If the wall thickness is 0.38", determine the tangential stress of the wall in psi.
A closed tank whose bottom is 18 inches in diameter is filled with three liquids: 4 inches of carbon tetrachloride (SG=1.59), 2 inches of water and 12 inches of syrup (SG=1.31). The air chamber in the tank is pressurized at 1296 psf. d. Apply the PANEL EQUATIONS to determine the magnitude, direction and location of the total hydrostatic force acting at the bottom of the tank.