The shaft is made of A992 steel with the allowable shear stress of Tallow = 75 MPa. Gear B supplies 15 kW of power, while gears A, C and D withdraw 6 kW, 4 kW and 5 kW, respectively. The shaft is rotating at 600 rpm. (Figure 1) Figure 600 mm 600 mm ② 600 mm < 1 of 1 > ▼ Part A Determine the required minimum diameter d of the shaft to the nearest millimeter. Express your answer as an integer. ΠΑΣΦ11 Ivec d= Submit Part B Find the corresponding angle of twist of gear A relative to gear D. Express your answer using three significant figures. VE ΑΣΦΠ Ivec 1 PA/D= Submit Request Answer Provide Feedback Request Answer ? www. ? mm rad

The shaft is made of A992 steel with the allowable shear stress of Tallow = 75 MPa. Gear B supplies 15 kW of power, while gears A, C and D withdraw 6 kW, 4 kW and 5 kW, respectively. The shaft is rotating at 600 rpm. (Figure 1) Figure 600 mm 600 mm ② 600 mm < 1 of 1 > ▼ Part A Determine the required minimum diameter d of the shaft to the nearest millimeter. Express your answer as an integer. ΠΑΣΦ11 Ivec d= Submit Part B Find the corresponding angle of twist of gear A relative to gear D. Express your answer using three significant figures. VE ΑΣΦΠ Ivec 1 PA/D= Submit Request Answer Provide Feedback Request Answer ? www. ? mm rad

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A 5 ft long solid SAE4340 OQT1000 steel shaft is required to transmit a power of 180 HP. The shaft speed is 3,000 rpm. The allowable shear stress is 50 ksi and the allowable angle of twist per foot of length is 0.04 radians. Determine the minimum diameter that meets the design requirements. Note- Shear modulus for steel is given in images
A propeller shaft is required to transmit 45 kW power at 500 rpm. It is a hollow shaft having inside diameter 0.6 times the outer diameter. It is made of plain carbon steel and the permissible shear stress is 84 N/mm^2. Determine the inner and outer diameters of the shaft.
Torsion Problem 6.0 A solid steel shaft is to transmit 5 hp from the motor to which it is attached. If the shaft rotates at w=160rpm and the steel has an allowable shear stress T=14 ksi, determine the required diameter of the shaft.
The shaft below is made of A992 steel and has an allowable shear stress of tadm = 75 MPa. When the shaft is rotating at 300 rpm, the motor provides 8 kW of power, while gears A and B draw 5 kW and 3 kW, respectively. Determine the minimum diameter required for shaft. Also, find the angle of twist of the gear A with respect to C.