The ship is pushed through the water using an A-36 steel propeller shaft that is 8 m long. measured from the propeller to the thrust bearing D at the engine. • Part A If it has an outer diameter of 360 mm and a wall thickness of 55 mm, determine the amount of axial contraction of the shaft when the propeller exerts a force on the shaft of 5 kN. The bearings at B and C are journal bearings (Eigure 1) Expres your answer with appropriate units. ? 8 = Value mm Submit Request Answer Provide Feedback Next > Figure < 1 of 1

The ship is pushed through the water using an A-36 steel propeller shaft that is 8 m long. measured from the propeller to the thrust bearing D at the engine. • Part A If it has an outer diameter of 360 mm and a wall thickness of 55 mm, determine the amount of axial contraction of the shaft when the propeller exerts a force on the shaft of 5 kN. The bearings at B and C are journal bearings (Eigure 1) Expres your answer with appropriate units. ? 8 = Value mm Submit Request Answer Provide Feedback Next > Figure < 1 of 1

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
The strength per meter of the longitudinal joint in the figure is 480 kN, whereas or the girth joint is 200 kN. Determine the maximum diameter of the cylindrical tank if the internal pressure is 1.5 MPa.
Determine the volume of the body (s=3.0) that is required to keep the gate in the position indicated in the figure. The gate is 2.40m wide and 4.2m long.
Plate AB has a width of 1.5 m and a radius of 3 m. Determine the horizontal and vertical components of reaction at the pin A and the vertical reaction at the smooth stop B due to the water pressure. Strictly using General Solution, and please show pressure diagram.
A water tank 3m in diameter and 6m high is made from 12mm thickness of steel. When the tank is filled with water: - Determine the circumferential stress - And the tension force in the vessel
Using the figure Determine the reaction force on the smooth support at B due to the fluid pressure on the gate. The width of the gate into the page is 1.5 m and the density of the water is 1000 kg / (m3) .
The gas tank consists of a cylindrical section with two hemispherical endcaps. The cylinder has a diameter of 75 cm and a wall thickness of 2 cm. If the allowable circumferential stress is 150 MPa and longitudinal stress is 100 MPa, find the maximum allowable internal pressure in the tank. Answer: P = ___________________
The round handle of a faucet is affixed to a shaft that lets a valve to be open and closed every time the round handle is rotated. Give the radius of the handle if the shaft has a diameter of 1 cm and the MA of the machine is 8.
A vessel cylindrical in shape and closed at the top and bottom is 300 mm in diameter, 1 m long and contains water up to a depth of 0.8 m. The air above the water surface is at a pressure of 60 kN/m2 . If the vessel is rotated at a speed of 250 r.p.m. about its vertical axis find the pressure head at the bottom of the vessel (i) At the centre, and (ii) At the edge
A cubical tank of 2 m side contains oil of relative density 0.8 to t depth of 0.6 m and sea water of relative density 1.024 to a depth of 1 m. Calculate the pressure on the bottom of the tank and the total thrust on one side of the tank. Determine also the position of the center of pressure above the base. Ans. 14.8 kN/m2, 22.31 kN, 0.512m
Both the top of the tank and the end of the slanted tube are open to the atmosphere. If L = 3.65 m., x = 98 cm., y = 94 cm., SG1 = 0.98, SG2 = 1.88, what is the angle of tilt (in degrees) of the tube? Accepted answer ranges from 22.42-24.422. Show solution.
PLEASE ANSWER THEM ASAP ALL FOR AN UPVOTE. I PROMISE THAT. At 20 0 C, determine pressure (in N/m²) inside a water droplet having diameter of 1.5 mm with a surface tension of 0.053 N/m. a.) What is the working formula of pressure to be used in this problem? b.)What is the diameter of the droplet (in m - enter your complete answer in decimal system)? c.) What is the radius of the droplet (in m - enter your complete answer in decimal system)? d.) What will be the modified working equation to be used to solve this problem based from the given? e.) What is the pressure inside the droplet of water (in N/m²)? f.)What is the pressure inside the droplet of water (converted to its CGS unit)?