9-127. The 2-m-wide rectangular gate is pinned at its center A and is prevented from rotating by the block at B. Determine the reactions at these supports due to hydrostatic pressure. pw = 1.0 Mg/m³.

9-127. The 2-m-wide rectangular gate is pinned at its center A and is prevented from rotating by the block at B. Determine the reactions at these supports due to hydrostatic pressure. pw = 1.0 Mg/m³.

Name: 9-127. The 2-m-wide rectangular gate is pinned at itscenter A and is
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 9-127. The 2-m-wide rectangular gate is pinned at itscenter A and is prevented from rotating by the block at B.Determine the reactions at these supports due to hydrostaticpressure. pw = 1.0 Mg/m³..09sbuningA.VRDCPr69-130. The semicircular -Determine

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

Consider a heavy car submerged in water in alake with flat bottom. The driver's side door of the car is1.1 m high and 0.9 m wide, and the top edge of the door is10 m below: the water surface Determine the net forceacting on the door ( normal to its surface) and the locationof the pressure center if : (a) the car is well-sealed and itcontains air at atmospheric pressure and (b) the car is filledwith water. (Ans:102.5 kN)
Determine the volume of the body (s=3.0) that is required to keep the gate in the position indicated in the figure. The gate is 2.40m wide and 4.2m long.
The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
Determine the capillary rise of the water in the glass tube of diameter 0.35cm, which is immersed vertically in the glass vessel.The surface tension of water is 0.07213 N/m.Take the contact angle of water as theta = 00 The capillary raise of water in the tube is (unit in m)=
A Horizontal Capillary Tube (Radius 10 Um) Con- Tains An Oil/Water Interface. The Pressure In The Oil Phase Is 14.5 Psi (100 KPa). Determine The Pressure In The Water Phase If The Contact Angle Is 30° And The IFT Is 30 Dynes/Cm (30 MN/M).
Determine the capillary rise of water in the tube of diameter 0.64 mm when immersed in a tank. Take surface tension between the water and tube as 0.073 N/m. 0.0465 m 46.5087 m 0.0047 m 0.4562 m
Determine the distance (h) in mm ,that a column of mercury in the tube will be depressed when the tube is inserted into the mercury at a room temperature of 20°C. Set ( D= 12 ) mm , density of mercury =13550 Kg/m3 , (s) surface tension 37.5x10-2 N/m , a= 42 o The Value of theata is equal to ? The Value of (h) is equal to?
Determine the distance (h) in mm ,that a column of mercury in the tube will be depressed when the tube is inserted into the mercury at a room temperature of 20°C. Set ( D= 6 ) mm , density of mercury =13550 Kg/m3 , (s) surface tension 37.5x10-2 N/m , a= 57 o 2- The Value of (h) is equal to .....?
A 4-m-high, 5-m-wide rectangular plate blocks the end of a 4-m-deep freshwater channel, as shown inthe Figure 2 below. The plate is hinged about a horizontal axis along its upper edge through a point Aand is restrained from opening by a fixed ridge at point B. Determine the force exerted on the plate bythe ridge. Clearly state all asuumptions and illustrations.
Using the figure Determine the reaction force on the smooth support at B due to the fluid pressure on the gate. The width of the gate into the page is 1.5 m and the density of the water is 1000 kg / (m3) .
An experiment was conducted using a communicating vessel to knowthehydraulic pressure. The communicating vessel consists of two column, XandY. Column X has a diameter of 15 cm and column Y of 75 cm. Oil (s = 0.852) wasfilled to the communicating vessel. A load of 1275 N was given to the columnY. Determine the minimum force that should be given to column Xso that theload can be lifted and the density of oil !
two vertical parallel glass plates 0.1 mm apart are partially immersed in water. Considering that the water does not reach the upper edges of the sheets and that the liquid completely wets the glass, determine: a) the height that rises in the flat capillary, b) the attractive force between the plates. Consider the width of the sheet l=12cm and density y=72.8*10^-3 N/m