The shorter the __ is, the more force the lever will apply. A. Fulcrum  B. Acceleration  C. Load Arm (answer only)

Q: Applying finger pressure on the belt near the pulley end is the correct method to check the tension…

A: True

Q: Explain the job of Rudder

A: The rudder is a primary flight control surface that controls rotation about the vertical axis of an…

Q: What approach does a utilitarian would do if he/she is to solve the trolley problem (lever switch)?…

A: Given Trolley To find Utilitarian approach for trolley problem

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: how will a vehicle handle if it has too much toe-out?

A:

Q: when the bottom of a control arm is toward the front of the car and the point turns in to meet the…

A: A trailing arm is a type of independent rear suspension which has the pivot axis precisely…

Q: What types of traction machines are used for hoisting elevators?

A: Given Data→ Traction machines Hoisting elevators

Q: 4. Briefly describe a lever and explain how a lever operating at a mechanical advantage differs from…

A:

Q: 11. Soru We use belts and pulleys in an assembly for Fill in the blank with correct option. O A)…

A: A belt and pulley is a mechanical system. This system contains two or more pulleys with a common…

Q: Explain the Jog/shuttle mechanism.

A: The explanation about the Jog/shuttle is given as under.

Q: Draw a detailed with explanation Free Body Diagram of a Tripod

A:

Q: Which therbligs correspond to which activities? 1.Lift and move wrench toward screw 2.Reposition…

A: Solution:

Q: 21:compare • Packed Hole Assembly • Pendulum Assembly • Fulcrum Assembly

A: Bottom hole assembly  There are numerous components and equipment (including the drill bit) that are…

Q: HiW.2 え-? static 14cm Ans. 文。1.6 Cm locm 5um 14cm 20 cm 133 CamScanner - W ia gal

A: Answer: The location of x-centroid is 11.6 cm.

Q: 16. When a pneumatic solenoid fails, the failure is normally due to a O A. weak pilot. O B. bad…

A: When seal is damaged, the valve does not shut off properly. after a close inspection damaged…

Q: and the restorer

A:

Q: Identify the material handling equipment which can move in a fixed path and has a cantilever support…

A: In jib crane can move in a fixed path and has cantilever support and in bridge crane has two…

Q: The high tension side of belt is known as tight side Select one: True

A: Given: Belt pulley system

Q: 1. Which sprinting techniqu uds effective: flexing the knee swing leg more during the

A: Sprinting technique is nothing but the forward momentum given focusing on the adjustments in your…

Q: the carrying cost

A: Given; Company has annual demand of, 1000 units,  ordering  cost =Rs 100/ ordercarrying cost = Rs…

Q: Which of the following works by dragging a bucket towards the machine? Dragline Clamshell O Loader…

A: It is required to determine which machine works by dragging a bucket

Q: M- mass that can what is the maximum mass be hung fremy the keep?

A:

Q: rest position to the upright unstable equilibrium position.

A: Introduction The truck pendulum framework is an ordinary benchmark issue in the control field. It is…

Q: 1. When does a mechanism reach the toggle positions.

A: NOTE: According to our expert guidelines we are supposed to answer only one question at a time.…

Q: A bridge crane is a material handling equipment that can lift load and unload which can rotate in a…

A:

Q: What is the difference between a long position and a short position?

A: Long Position If an investor has long positions, it means that the investor has bought and owns…

Q: In Slider crank mechanism, if the time required for movement of crank for both forward and reverse…

A: Answer    Quick return mechanism

Q: What are the inversion of single slider mechanism when connecting rod is fixed?

A: Given: When one link is fixed in a mechanism it will work like a machine and gives the directional…

Q: The simplest type of balance for weighing is the___________.

A: To balance the weight, there are multiple possible lever arrangement. One such example is shown…

Q: Briefly discuss, how the energy consumptions for operations of a fork lifter could be justified.

A: On average, one forklift consumed 65 L of diesel fuel per day, 7 L per hour, 1.6 L per load, 0.7 L…

Q: To move something that weighs more than you do, using a lever, move the item closer to the __. A.…

A: A lever is consist of three parts Fulcrum is the fixed point around which the bar pivots Effort arm…

Q: The amount of force generated by an air bearing decreases when?

A: The amount of force generated by an air bearing decrease when

Q: What is the forklift trucks system?

A: Forklift trucks are the industrial vehicles used for transportation of cargo from one point to…

Q: stiffness (in N/m) of the required mounting pad

A: Given; A precision instrument package m= 1 kgSurface vibrating at= 60 HzIsolation is designed with…

Q: specific weight is also known as weight. select one: True False

A: Answer: False

Q: Derive an expression for the height of propell governor

A: Governors are the most effective way to manage or regulate an engine's speed based on variable…

Q: Where are the application of slider crank mechanism? Answer at least five applications

A: Slider Crank Mechanism is most widely used mechanism, they are used in a number of places like, 1.…

Q: flyw

A: compare governor and flywheel

Q: T. A T (N) 750 FRAGILE HANDLE CARE ON' 5 8 t (s ?

A: Given: mass of the package =  106.5 kg

Q: platform weighing machine

A: From very early times, civilizations used weighing machines in business transactions. Over the…

Q: What is the purpose of using the centrifuge

A:

Q: resistance to motion caused by the shoveling

A: Given: Q= 12 ft3/s V=14 ft/s specific weight =5.5 lb/ft3 TO determine: resistance to motion

Q: In Slider crank mechanism, if the angle required for movement of crank for both forward and reverse…

A: Off set slider crank mechanism is a quick return mechanism. So, the angles will not be same. In…

Q: out and Tagout

A: given: Explain the difference between Lockout and Tagout

Q: (a) Explain in detail the main difference between the drop platform truck and drop center baggage…

A: A platform truck is a flat sheet of metal that has wheels on the bottom and a handle on the back,…

Q: For the description of machine, mechanism, link and parts, ( _____) is correct. A.Parts is motion…

A: For a description of machine there  is requirement of frame which should have relative motive to…

Q: A Hartnell governor is a governor of the dead weight type pendulum type O inertia type spring loaded…

A: Given: A Hartnell governor is a governor of the O dead weight typeO pendulum typeO inertia type O…

Forced undamped vibrations

In mechanical engineering, vibration is expressed as the term that occurs due to an object's backward and forward movement about a point of equilibrium. Generally, there are three types of vibrations which are,