The shower head shown in the Figure delivers water at 50°C. An orifice-type flow reducer is to be installed. The upstream pressure is constant at P=------ kPa. Drive the formula and estimate the water flow rate from the shower head. Use your last three digits of your number for the upstream pressure P= kPa. Flow reducer 40 holes 2 mm diameter 00 00000 000000 0000000 0000000 0000000 000000 00000

The shower head shown in the Figure delivers water at 50°C. An orifice-type flow reducer is to be installed. The upstream pressure is constant at P=------ kPa. Drive the formula and estimate the water flow rate from the shower head. Use your last three digits of your number for the upstream pressure P= kPa. Flow reducer 40 holes 2 mm diameter 00 00000 000000 0000000 0000000 0000000 000000 00000

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe of 0.25 m diameter carries water at the rate of 7.2 m3/s.The pressure head at the entry of the venturimeter, used to measure the flow rate in the pipe, is equivalent to 6 m of water. If the pressure head at the throat is zero, calculate the throat diameter of the venturi.Include fbd.
Two pipes, one circular and one square have the same cross-sectional area. Which has the larger hydraulic radius ? Show your solution to prove your answer
A 230-m-long pipeline delivers 20◦C water to a storage reservoir located downstream. The pipeline is galva-nized with an average roughness height of 0.2 mm. An axial pump is used to pressurize upstream water. Thewater surface in the reservoir is located 18 m above the centerline of the pump. The pump discharges waterat an absolute pressure of 400 kPa and a volume flow rate of 50 L/s. Calculate a diameter of pipe requiredto achieve such an operating condition. If needed, use the Moody diagram on the last page, or one can solvethe Colebrook equation using, for example, Matlab.
Water at 20°C is pumped through a smooth 12-cm-diameter pipe 10 kmlong, at a flow rate of 75 m3/h. The inlet is fed by a pump at an absolute pressure of 4 MPa.The exit is at standard atmospheric pressure (101 kPa) and is 200 m higher. Calculate the frictional head loss Hf and compare it to the velocity head of the flow.
For this siphon the elevations at A, B, C, and D are: 30 m, 32 m, 27 m, and 26 m, respectively. The head loss between the inlet and point B is three-quarters of the velocity head, and the head loss in the pipe itself between point B and the end of the pipe is one-quarter of the velocity head. For these conditions, what is the discharge and what is the pressure at point B? The pipe diameter 25 cm.
Flowrate of water through bend pipe (90o) is 0.21 m3/s. The pipe diameter at the inlet is 150 mm andthe outlet diameter is 75 mm. The outlet is higher than the inlet by 2 m. Frictional losses in the pipe isequal a loss factor of 0.5 applied to the inlet velocity head. The pressure head at the inlet is 8.6 m andthe volume of water in the bend is 0.6 m3. Calculate the resultant force and its direction.
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa (indicate the sign if negative) Decimal Places required in the final answer: 3
Water (ρ=998 kg/m³, μ=1.02x10^-3 kg/ms) flows through a 598 m length of pipe with 150 mm in diameter at 60 L/s. Determine the pipe roughness, ɛ if the head loss is 49 m.
A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a pressure of 150 kPa. The throat diameter of the me- ter is 100 mm and the pressure at the throat is 400 mm of mercury below atmosphere. If 3% of the differential pressure is lost between inlet and the throat, determine the flow rate of the pipeline. PLEASE USE BERNOULLI'S ENERGY EQUATION. INCLUDE COMPLETE SOLUTION
1. A hydroelectric plant has 20 MW generator with an efficiency of 96 %. The generatoris directly coupled to a vertical Francis type hydraulic turbine having an efficiency of 80%.The total gross head on the turbine is 150 m while the loss of head due to friction is 4 %of the gross head, the runaway is not to exceed 750 rpm. Determine the flow of waterthrough the turbine in m3/s. Complete Solution/s (i.e. transformations, equivalent formula, etc).
Two pipes are connected in series with a diameter ratio of 2:5. If the flow velocity in the smaller diameter pipe is 12 m/s, determine the head loss due to: a. sudden contraction, b. sudden enlargement.
kindly help me with this problems INSTRUCTIONS: Solve the problems neatly and systematically. SUse free-floating decimals in all your calculations and in expressing your answers. Box your final answers. 2. Water in a partially filled large tank is to be supplied to the rooftop, which is 8 m above the water level inthe tank, through a 2.5 cm internal diameter pipe by maintaining a constant air pressure of 300 kPa (gauge) inthe tank. If the head loss in the piping system is 2 m of water, determine the discharge rate of the supply ofwater to the rooftop in L/s