The hollow rectangular cross-sectioned beam (200 mm wide and 400 mm deep with 10 mm thickness) shown below supports a uniform load of w = 10 kN/m throughout its length and a concentrated load of P = 20 kN (3 m from the left end of the beam). Determine the following: P = 20 kN 3 m W = 10 kN/m %3D 6 m 1 m R1 R2 10 mm 10 mm 200 mm- 10 mm 10 mm ww 00t

The hollow rectangular cross-sectioned beam (200 mm wide and 400 mm deep with 10 mm thickness) shown below supports a uniform load of w = 10 kN/m throughout its length and a concentrated load of P = 20 kN (3 m from the left end of the beam). Determine the following: P = 20 kN 3 m W = 10 kN/m %3D 6 m 1 m R1 R2 10 mm 10 mm 200 mm- 10 mm 10 mm ww 00t

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.9P

See similar textbooks

Similar questions

In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=75° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm2 and A=50 cm2 shall be taken for all rods.)
A block with mass m=(24+12)kg is pulled by a horizontal force P applied at point B in Fig.3. The coefficient of kinetic friction between the surfaces is we = (5A+5)/(25+94). When the acceleration of the block is a=(1+9)/4 m/s?, determine the cable forces Tax and Top- 0=(A+8) A=1
The 426-kg uniform beam is subjected to the three external loads shown. Compute the vertical reaction (N) at the support point O if P = 4189 N, Q = 3243 N, T = 40187 Nm, x = 1.02 m, y = 1.43 m, and z = 1.56 m and the system is in equilibrium.Positive values are to the right, up, and counterclockwise. Round off only on the final answer expressed in 3 decimal places.
Given the ff. data of dynamic lateral force procedure for buildings:Period of vibration: T = 0.8 secSpectral velocity, Sv = 0.15 m/secK = 15 158 kN/mmTotal W = 2400 kN Give the maximum relative displacement,the value of spectral acceleration,value of the lateral force of the tank in kN,the value of the maximum base shear in kN.
The cantilever beam shown is subjected to a couple and 2 forces shown. Replace these couple and forces with an equivalent couple M and single force F at point A. Show solution to the answer FH = 1.64 kN, R Fv = 1.16 kN, D M = 2.22 kN-m, CCW
Determine the resultant of the vertical thrusts on the sphere shown in the figure for the data: d=0.6m; R=0.5m;h=4m.
For the beam loaded as shown in the figure 2, determine the moment reaction at A in kN-m using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E = 80 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 2.9 m, b = 32.9 kN/m, c = 20 kN.
E1= 7 GPA E2= 10 GPA P= 7000 kN V = 40 kN
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
PROBLEM 1: The homogeneous structure shown weighs 21.45 kN per square meter of cross-section. The structure is subject to horizontal uniformly distributed load P1 and triangularly distributed load P2 perpendicular to side AB. Given: H1 = 9 m; H2 = 6 m; H3 = 12 m X1 = 6 m; X2 = 5 m P1 = 220 kN/m; P2 = 280 kN/m 4 Magnitude of resultant, R 4314.04 5 Angle of resultant direction from x-axis, θx 86.01 6 Distance of resultant from C measured along line CD, X 9.116
A block weighing 100 N is placed on an inclined plane of slope angle 30 degrees and is connected to a secondhanging block of weight “W”, by a cord passing over a small frictionless pulley. The coefficient of slidingfriction is 0.3. Find the weight “W” for which the 100N block moves up the inclined plane at a constantvelocity.
A reinforced concrete beam has a width of 400mm and an effective depth of 600mm. It is reinforced for tension with 4-28mm rebars. F'c = 20.7MP and Fy = 414.6MPa. 7. Determine the ultimate moment capacity. a 484.76KN.m b. 448.67KN.m 8. Determine the percent increase in ultimate b. 34.4% a. 25.1% c. 487.46KN.m d. 446.87KN.m moment if depth is increase to 700mm. c. 18.98% 15.68%