The simply supported beam carries three concentrated loads as shown in the figure. Determine the beam deflection at a section 5.74 feet from the pin support if P = 3327lb, Q =5726lb, R = 7383lb, E = 27348 , and I = 471. Round off your answer to 6 decimal places. y P Q + 3 ft>+ 3 ft 3 ft→+ 3 ft→| Add your answer

The simply supported beam carries three concentrated loads as shown in the figure. Determine the beam deflection at a section 5.74 feet from the pin support if P = 3327lb, Q =5726lb, R = 7383lb, E = 27348 , and I = 471. Round off your answer to 6 decimal places. y P Q + 3 ft>+ 3 ft 3 ft→+ 3 ft→| Add your answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Using ANY GEOMETRIC METHOD Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 5.6 m b = 4.4 m c = 15.9 kn/m d = 22 kn QUESTIONS: 1. Determine the VERTICAL REACTION at B in KN. 2. Determine the SLOPE at B in DEGREES. 3. Determine the DEFLECTION at D in MM. 4. Determine the DEFLECTION AT MIDSPAN OF THE BEAM in MM. Thank you! Please answer all. ❤️
15. Compute the resultant of the three forces shown in the figure. A. 894.32 N B. 836.90 N C. None of the Above D. 315.28 N E. 948.27 N
Given the problem: The smooth disk shown in the figure is pinned at 'D' and has a weight of 24.6 lb. Neglecting the weights of the other members, determine the following: d.) Horizontal component at 'D' in lb. e.) Vertical component at 'D' in lb. *Round off final answer in 4 decimal places. Thank you.
Compute the resultant of the three forces shown in the figure. a.) None of the Above b.) 315.28 N c.) 836.90 N d.) 894.32 N e.) 948.27 N
A horizontal force P acts on the top of the 30 N block having a width of 25 cm and a height of 50 cm. If the coefficient of friction between the block and the plane is 0.33. a. What is the value of P for motion to impend? b. Is the motion will impend due to overturning?
Need help experts. The rigid body shown in the figure is subjected to the indicated force system. Determine the forces applied at points A and E that equal the applied force system.Data: β = 48°; a = 6,6 m; b = 8,9 m; F = 31 kN; P1 = 20,743 kN; P2 = 23,037 kN The force applied at point A is FA = ? Answer kN and the force applied at point B is FB = ? Answer kN.
Given beam loaded as shown below. Assuming EI is constant. 1. Which of the following gives the location of maximum deflection. a. 2.212 m b. 1.958 m c. 1.334 m d. 1.456 m 2. Which of the following the value of maximum deflection. a. 29.4/EI b. 17.5/EI c. 20.7/EI d. 14.2/EI
Need answer ASAP. Please be detailed and clear with your solution. IV. The corner of a floating body has a quarter cylinder AB having a length normal to the paper of 3 m. 8) Calculate the magnitude of the horizontal component of the force on AB in kN. *9) Calculate the magnitude of the vertical component of the force on AB in kN. *
A cantilever beam carries a varying load as shown in the figure. If E = 200,000 Mpa and I=120×10^6 mm^4 Determine the following. Use Double Integration Method 1. Slope at free end 2. Deflection at 4m from the support
Using DOUBLE INTEGRATION METHOD. Consider 150 mm x 150 mm section and E = 200 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 3.5m b = 16 kn/m c = 16 kn QUESTIONS: 1. Determine the REACTION at A in KN. 2. Determine the SLOPE at A in DEGREES. 3. Determine thw DEFLECTION at B in MM. 4. Determine the DEFLECTION at E in MM. THANK YOU!
A 7.5m cantilever beam shown carries a 115KN/m uniform load. Point A is free end while point B is fixed support. Using Double Integration Method with origin at point A, calculate the value of EIy' at the free end in KN-m2. Express your answer in 2 decimal places. Please show complete solution
Q.2 Three bars each made of different materials are connected together and placed between two walls when the temperature is T1 = 12 oC. Determine the force exerted on the rigid supports when the temperature becomes T2=18 oC. The material properties and crosssectional area of each bar are given in the figure.