The simply supported beam is built up from three boards by nailing them together as shown. m 1 m 100 mm 25 mm 25 mm 200 mm 25 mm The applied force is P= 13.9 kN. The nails are each able to resist a shear force of 1.7 kN. Part A Determine the maximum allowable spacing of the nails. Express your answer to three significant figures and include appropriate units.

The simply supported beam is built up from three boards by nailing them together as shown. m 1 m 100 mm 25 mm 25 mm 200 mm 25 mm The applied force is P= 13.9 kN. The nails are each able to resist a shear force of 1.7 kN. Part A Determine the maximum allowable spacing of the nails. Express your answer to three significant figures and include appropriate units.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.4.3P: Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the...

See similar textbooks

Similar questions

The following box beam is constructed from four boards that are fastened together using nails. Aforce P is applied to the end of the beam, 8ft from the fixed support. There is a compressive 500lbforce applied horizontally at the bottom of the beam. The nails used to support the bottom board(at A) are spaced every 3 inches and the nails along the top board (at B) are spaced every 2 inches. a. The nails can support a force F = 350 lb. Based on the strength of the nails, determine themaximum allowable force P that can be applied to the beam as shown.
It is obtained by fixing 4 wooden planks to each other with nails.given as a cross section. 2 verticals forming the sectionplank 20 mm X 80 mm, the other two planks 20 mm X 120 mmin size. between the nails fastening the planksthe distance is s = 50 mm. allowed on each nailThe safe cutting force is 300 N. a) What is the highest vertical shear force that the beam can safely carry? b) What is the highest shear stress occurring in the section corresponding to this shear force?
The beam is made from four boards nailed together as shown. If the nails can each support a shear force of 100 lb., determine their required spacing s and if the beam is subjected to a shear of V = 700 lb.
The dimensions of a rectangular beam are limited to b = 300 mm and effective depth, d = 700 mm. Using f’c = 28 MPa, long bar fy = 415 MPa, calculate the required amount of tensile reinforcement so that a tensile strain of 0.005 is attained under a sustained ultimate bending moment of 1,200 kN.m. Compression bars centroid is 70 mm from beam edge. 5.353 3,839 4,387 6,180
The box beam of wood is constructed of two 220 mm x 29 mm boards (see figure). The boards are nailed at a longitudinal spacing s = 100 mm. If each nail has allowable shear force F = 1,000 N, what is the maximum allowable shear force Vmax? Round to one decimal place. Vmax = ___ kN
The timber member has a cross-sectional area of 1603 mm2 and its modulus of elasticity is 13.8 GPa. Compute the change in the total length (in mm) of the member after the loads shown are applied if x = 1.64, y = 3.37, and z = 4.57.
What is the midspan value of EI δ for the beam loaded as shown? Draw fbd.
With two rectangular plank nails cross-sectional bar in the shape by hammering into each other being created. Nail spacing a= 70 mm and If the shear force it can carry is V= 1.4 kN The shear force T that the section can safely carry is y find it.
Assume the sections have cracked and use the transformed area method to compute their flexural stresses for the loads or moments given PLEASE EXPLAIN THE STEPS OR FORMULAS USED I really want to understand professor gives equations and solutions but I am trying to understand how he gets some numbers thabk you so much for helping
TRUSS. Using the method of joints. Round off your answer into two decimal places. Eliminate all the zero-force members before analyzing. a. Determine force BE in kN, compression or tension? b. Determine force BC in kN, compression or tension? c.Determine force EF in kN, compression or tension? d. Determine force DE in kN, compression or tension? e. Determine force FG in kN, compression or tension?
Three boards, each 2 in. thick, are nailed together to form a beam that is subjected to a vertical shear. Knowing that the allowable shear-ing force in each nail is 150 lb, determine the allowable shear if the spacing s between the nails is 3 in.
A 3m both ends hinged timber column is made of Apitong wood with the following properties: Fc = 9.56 MPa (parallel to grain) Fc = 2.20 MPa (perpendicular to grain) E = 7310 MPaIf it has a square section with 200mm side dimension. Compute the actual slenderness ratio of the column. a. 12 b.13 c.14 d.15