The simply supported beam of channel cross-section carries a uniformly distributed load and a concentrated load as shown in the figure, determine the maximum tensile and compressive stresses in the beam. 60 kN/m 3m 50 kN 1m +1m 200mm - 150mm 25mm 25mm pr 25mm

The simply supported beam of channel cross-section carries a uniformly distributed load and a concentrated load as shown in the figure, determine the maximum tensile and compressive stresses in the beam. 60 kN/m 3m 50 kN 1m +1m 200mm - 150mm 25mm 25mm pr 25mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Taking into account only the effect of normal stresses, determine the strain energy ofthe prismatic beam AB for the loading shown. M0 (11kNm), L (3.4m), a (1cm), b (7cm) , d (14cm) , E (185GPa) , G (75GPa)
A distributed load of w N/m is applied over an entire length of a simply supported beam 8m long. The beam section is made up of four 20mmx100mm rectangles arranged as shown. Determine the following: a. maximum value of w without exceeding the permissible flexure stress of 10MPa. b. maximum value of w without exceeding the permissible shear stress of 1.2MPa. c. maximum value of w without exceeding the permissible screw strength of 800N for a pitch of 75mm.Please show your clean and complete solution. Thanks
Assume that 4-18mm diameter rivets join the plates that are each 120mm wide. The allowable stresses are 120MPa for bearing in the plate material and 60MPa for shearing of rivets. Determine the following:a. The minimum thickness of each plateb. The largest average tensile stress in the plate F=70
A bar of the rectangular cross-section is 100mm thick by 50mm broad and carries an axial compressive load of 160KN. If the line of action of the load is 12.5mm from the center of the thickness of the section along the centerline of the breadth. Determine the maximum and minimum stresses in the bar. Show complete process and solution. Given: F = W = 160KN x 1MN / 1000KN = 0.160MN B = 50mm x 1m / 1000mm = 0.50m T = 100mm x 1m / 1000mm = 0.1m X = 12.5mm x 1m / 1000mm = 0.0125m
A pre stressed concrete simple beam having a cross section of300mmx600mm is subjected to a pre stressing force in steel whicheventually reduce to 1200KN due to losses acting on a parabolic tendons.The beam carries a total uniform distributed load of 20 KN/m includingbeam’s weight. Using three methods calculate the total stresses at midspan section of the beam. Given:B = 300mmD = 600mmP = 1200KNW = 20 KN/mE @ mid span = 50 mmE @ end section = 0 mmL = 10 mm Det. the total stresses of the extreme bottom fiber at midspan using load balancing method. (Mpa)
A beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at the midspan. (MPa) Properties: Beam width = 270 mmBeam height = 375 mmWLL = 14.38 kN/mWDL = 18.41 kN/mSpan of the beam = 8 mPrestressing force = 481 kNeccentricity = 103 mm
The rivet group connects two narrow lengths of plate, one of which carries a 15 kN load. If the ultimate shear strength t of a rivet is 350 N/mm² and its failure strength in compression o is 600 N/mm², determine the minimum allowable values of rivet diameter d (mm) and plate thickness t (mm).
Compute the bending stresses in the beam shown, f'c = 28 MPa Es=200000MPa M=165 kN-m
QUESTION: The distributed load on the T-section beam shown below and moment affects. A is the fixed joint and B is the sliding joint. This beam is made of a ductile material with a yield stress (σak) of 1000 MPa. The thickness (depth) of the beam profile is t=6 mm. A) As a mechanical engineer, check the strength of this beam (in terms of Normal and Shear Stress) ? B) In order for the existing beam to run smoothly, two 100x25 mm plates made of the same material are planned to be welded to this beam. The mechanical engineer working in the factory told the welder to weld this piece under the beam (where the B point is). But the welder, regardless of what the mechanical engineer said, welded this plate to both sides of the existing T-section beam as shown below, thinking that it wouldn't matter anyway. As a mechanical engineer : 1) After welding these plates on both sides of the beam, as the welder did, find out whether the new beam will work smoothly or not by making the necessary…
A cantilever beam subjected to a concentrated load at the end of its 6m length. If the allowable shearing stress at the neutral axis is 2MPA, determine the maximum compressive stress in the beam due to the maximum allowable load P. Use a flange thickness of 100 mm. 400mm 600mm 100mm please include the details. thank you
The built-up cross-section of the 2.0-m, fixed-base column shown below comprises three 300-mm × 25-mm plates that are welded together. The column is subjected to a 300-kN compressive axial load and moments of 100 kN.m and 50 kN.m about the x and y axes, respectively, at its free end (top). Using Fusion 360, compute maximum tensile and compressive stresses (along z) at mid-height of the column (sufficiently far away from stress concentration zones) and compare them with your hand calculations.\ Answers will be: Cross-section area = 22500 mm2 (5 points) Ix = 453,125,000 mm4 (5 points) Sx = 2,589,286 mm3 (5 points) Iy = 112,890,625 mm4 (5 points) Sy = 752604.2 mm3 (5 points) Stress caused by the axial load = -13.33 MPa (5 points) Stress caused by Mx = ±38.62 MPa (5 points) Max Stress = 91.72 MPa (5 points) Min Stress = -118.39 MPa (5 points)
The cantilever beam shown in Figure P15.15a is subjected to concentrated loads Px = 18kips and Py = 32 kips. The cross-sectional dimensions of the rectangular tube shape shown inFigure P15.15b are b = 8 in., d = 12 in., and t = 0.25 in. Point H is located at a distance of a = 24in. to the left of the concentrated loads. Calculate the principal stresses and maximum in-planeshear stress at point H for the following values of h:(a) h = 4.0 in.(b) h = 6.0 in.(c) h = 8.0 in.FIGURE P15.15a FIGURE P15.15bP15.43 A solid steel shaft with an outsidediameter of 1.5 in. is supported in flexiblebearings at A and C as shown in FigureP15.43/44. Two pulleys are keyed to the shaft atB and D. Pulley B has a diameter of D B = 14 in.and belt tensions of T 1 = 100 lb and T 2 = 220 lb.Pulley D has a diameter of D D = 7 in. and belttensions of T 3 = 60 lb and T 4 = 300 lb. Lengthdimensions of the shaft are x1 = 8 in., x2 = 4 in.,x3 = 3 in., and x4 = 6 in. Determine the normaland shear stresses at point K on…