The singly reinforced concrete beamsection shown in the figure (not drawnto the scale) in made of M25 gradeconcrete and Fe500 grade reinforcingsteel. The total cross-sectional area ofthe tension steel is 942mm2. [2 Marks]450300As per Limit State Design of IS456:2000, the design moment capacity(in kN.m, round off to two decimalplaces) of the beam section, is

Answered: Image /qna-images/answer/33a682e4-fc23-422d-8452-c644ffb37218.jpg

Answered: The singly reinforced concrete beam…

Engineering

Civil Engineering

The singly reinforced concrete beam section shown in the figure (not drawn to the

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.6.3P

See similar textbooks

Similar questions

I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. IN.A=4*10mm* 80mm 100mm 60mm 60mm 1.5KN 2kN/m 1mal A |-----|- | Im ++ Im->> 3m 3kN/m
H.W A Solid Steel bar of dlameter 6omm and length 350 mm is Placed inside an aluminum cylinder öf Inside diameter Femm and out side d lameter Ilomm, a comPressive load of looo lais applied on the assembly, find the stresses in the bar and the cylinder ? take Est = 200GPa and EAl = F0GPan %3D Cover Plate 0.25mm d- do 35omm A lum. cylinder Steel bar
(1) Given A992 steel Ag = 10 in %3D KLy- 80, ry what is $ Pa=? = 60 the' column streugth design
Topic: COMBINED STRESS-AXIAL TENSION AND FLEXURE BENDING: STEEL DESIGN Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee Questions A Tension member with no holes is subjected to axial loads of PD=68kN & PL=64kN.It is also subjected with bending moments of MDy=40kN-m & MLy=55kN-m. Is themember adequate? Steel is of A992 Gr 50 Specs. Use LRFD. Neglect the weight of the beam. Section properties:Lp = 1.863 md=459.99mmtw=9.02mmzx= 1835x10^3 mm^4Lr = 5.305 mLb = 4.8 mbf=191.26mmtf=16mmSx=1611x10^3 mm^4 Sy=195x10^3 mm^4Zy=303x 10^3 mm^4 Cb=1.32
A single unequal angle 100 x 75 x 6 is connected to a 10 mm thick gusset plate at the ends with six 16 mm diameter bolts to the 100 mm of leg to transfer tension as shown in figure. What will be the block shear strength (in kN) of the angle section assuming that the yield and the ultimate stress of steel used are 250 MPa and 410 MPa respectively? ISA (100 × 75 x 6) -T 16 mm o bolt 10 mm 40 mm 40 mm| 40 mm 40 mm 40 mm 40 mm 10 mm
2. A column HP 14 x 102 of A572 Gr. 55 steel has a length of 15 ft is fixed at both ends. Compute the design compressive strength for LRFD and the allowable compressive strength for ASD. (Steel section properties are provided in the next page) ASTM Designation A572 Gr. 42 Gr. 50 Gr. 55 Gr. 60⁰ Gr. 65⁰ Yield Stress (ksi) 42 50 55 60 65 Fu Tensile Stressa (ksi) 60 65 70 75 80
The angle L 8 x 8 x ½ in tension shown in the figure below must resist aservice dead load of 35 kips, live load of 50 kips, and a roof live load of 2kips. The steel used is A50 (Fy = 50 ksi, Fu = 65 ksi) and its welding length is 4”.Determine if the member has sufficient fracture and yield strength.
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
1. If the allowable stress of a revolving steel is 150 MPa, what is the equivalent angular velocity which will produce such stress. The mean diameter is 440mm. 2. See connection figure below. The rivets is 7/8 in. in diameter. According to the rivert supplier, the allowable stresses for the material are t = 15 ksi and Ob = 32 ksi. What is the allowable load of the connection? L4 x 3-1/2 W18 x 86 W24 x 117 Girder Beam
STRENGTH OF MATERIAL(SIMPLE STRESS) PLEASE INCLUDE FBD 100% GUARANTEE UPVOTE
TENSION MEMBERS: THE SINGLE 200 X 10 mm STEEL PLATE IS CONNECTED TO A 12 mm THICK STEEL PLATE BY FOUR 16 mm DIAMETER RIVETS AS SHOWN IN THE FIGURE. THE RIVETS USED ARE A502 GRADE 2, HOT DRIVEN RIVETS. THE STEEL IS ASTM A36 WITH Fy = 248 MPa AND Fu = 400 MPa. DETERMINE THE VALUE OF P. a. P BASED ON TENSION OF GROSS AREA b. P BASED ON TENSION OF NET AREA c. P BASED ON BEARING OF PROJECTED AREA d. P BASED ON SHEAR RUPTURE (BLOCK SHEAR)
SITUATION 14: A PL 300 x 20 mm is to be connected to two plates of the same material with half the thickness by 25 mm Ø rivets as shown in the figure. The rivet holes have a diameter 2 mm larger than the rivet diameter. The plate is A36 steel with Fy= 250 MPa, allowable tensile stress of 0.60Fy and allowable bearing stress of 1.35Fy. The rivets are A502, Grade 2, hotdriven rivets with allowable shear stress of 150 MPa. 25 mm Ø rivets + + PL 300x20 P/2 P P/2 PL 300x10 43. Which of the following most nearly gives the max. load in kN that can be applied to the connection without exceeding the allowable shear stress in the rivets? a. 675 KN b. 490 KN c. 598 KN d. 790.5 kN 44. Which of the following most nearly gives the max. load in kN that can be applied to the connection without exceeding the allowable bearing stress between the plates and the rivets? a. 490 KN b. 675 KN c. 598 KN d. 790.5 kN 45. Which of the following most nearly gives the max. load in kN that can be applied to the…