Please answer as soon as possible, thank you. The slide in a pipe is to be opened and closed. Actuation is to be triggered by meansof a valve with selector switch. A double-acting cylinder Is to be used as the drive.• The slide is to open/close only gradually since the load on the pipe wouldotherwise, be to great (the formation of surges is to be avoided).1. Design the pneumatic circuit diagram.2. Carry out the assembly.3. Check the assembled circuit.4. Describe the mode of operation of the circuit.5. Compile an equipment list6. Observe the pressure ratios upstream and downstream of the flow control valveand document these.Wastewater treatment1. If the selector switch is actuated, the cylinder is to advance and open up flow.2. If the selector switch is reset, the cylinder is to return into the initial position andthe slide is to close.

Solution: The Pneumatic circuit diagram is shown below:

The slide in a pipe is to be opened and closed. Actuation is to be triggered by means of a valve with selector switch. A double-acting cylinder is to be used as the drive. • The slide is to open/close only gradually since the load on the pipe would otherwise, be to great (the formation of surges is to be avoided). 1. Design the pneumatic circuit diagram.

The slide in a pipe is to be opened and closed. Actuation is to be triggered by means of a valve with selector switch. A double-acting cylinder is to be used as the drive. • The slide is to open/close only gradually since the load on the pipe would otherwise, be to great (the formation of surges is to be avoided). 1. Design the pneumatic circuit diagram.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter16: Advanced Automatic Controls-direct Digital Controls (ddcs) And Pneumatics

Section: Chapter Questions

Problem 3RQ: One advantage of a modern control system is A. simplicity. B. faster response. C. ability to...

See similar textbooks

Similar questions

For the pneumatic circuit in the figure, name each of the components and describe their operation (what each action does).
Made to reduce the coefficient of resistance (CD) on an object. Explain 3 of the control mechanisms by drawing a figure.
Design the electro -hydraulic circuit for the lifting and shifting operation as shown in Figure 2 with the following requirements. Following are the sequence of operation. Products are required to be transferred from lower level conveyor to higher level conveyor using two hydraulic Cylinders (Cylinder A and Cylinder B) and a conveyor belt (semi rotary motor) Cylinder A lifts the product on receiving it at lower level to the platform. Then, Cylinder B shifts the product from the platform to the conveyor, Then the conveyor motor should be rotated after 5 seconds to transfer the product to packaging Repeat the sequence of operation for 10 trials. NOTE: use independent DCV for each actuators (Cylinder A, Cylinder B and Conveyor motor)
ass 4. vib . Give detailed description of at least two methods of vibration control.
What is the mechanical advantage of the system shown below?
One advantage of a modern control system is A. simplicity. B. faster response. C. ability to modulate. D. that they are less expensive.
Block diagram and explanation of the applications of open loop system: Automatic washing machine, Automatic toaster system, Traffic light controller and Furnace without thermostatic control but with timing device
What is the function of a pneumatic actuator?
Describe the working of a hydraulic circuit which is used for sudden need of power source in the circuit which uses double acting cylinder with 5/2 with mechanical,electrical and manual method of actuation and also use other appropriate components with a neat circuit diagram and its parts name.
In a belt drive design, the angle of wrap correction factor C θ is a function of the angle of wrap of the belt on the small sheave. If in a design, the angle of wrap of the belt on the small sheave is 1500 , then C θ = ________ 0 .
For a vertically mounted hydraulic actuator with an overrunning load, what is the major disadvantage of using a counter balance valve to prevent a weight from falling uncontrollably and how can it be overcome?
Describe one of control section component which is used to operate double acting cylinder of having 3 position and 4 ports with the electrical, mechanical and manual method of actuation.