A 02-series single-row deep-groove ball bearing is to be selected from Table 11-2 for the application conditions specified in the table. Assume Table 11–1 is applicable if needed. The value of radial load Fr= 8 kN, axial load Fa= 3 kN, design life LD= 10°, ring rotation factor V= 1.2, and reliability RD= 0.95. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the C10 value for this application. The C10 value for this application is kN.

A 02-series single-row deep-groove ball bearing is to be selected from Table 11-2 for the application conditions specified in the table. Assume Table 11–1 is applicable if needed. The value of radial load Fr= 8 kN, axial load Fa= 3 kN, design life LD= 10°, ring rotation factor V= 1.2, and reliability RD= 0.95. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the C10 value for this application. The C10 value for this application is kN.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need right answer. Select a single row deep groove ball bearing for a radial load of 4000 N and an axial load of 5000 N, operating at a speed of 1600 rpm for an average life of 5 years at 10 hours per day. Assume uniform and steady load.?
Consider the belt drive having a diameter of 150 mm that is mounted on the overhung end of ashaft, 30 mm from the nearest bearing. The stepped shaft is made of steel having Su = 965 MPa(140 ksi). The shaft diameter, d, is 30 mm. The bearing bore, D, is 36 mm. The fillet with amachined surface has a radius, r, of 3 mm. What is the safety factor with respect to eventualfatigue failure of the shaft?
A certain application requires a ball bearing with the inner ring rotating, with a design life of 26 kh at a speed of 455 rev/min. The radial load is 2.5 kN and an application factor of 1.2 is appropriate. The reliability goal is 0.92. Find the multiple of rating life required, xD , and the catalog rating C10 with which to enter a bearing table. Choose a 02-series deep-groove ball bearing from Table 11–2 and estimate the reliability in use.
A rolling contact bearing is subjected to the following work cycle: (a) Radial load of 6000 N at 150 r.p.m. for 25% of the time; (b) Radial load of 7500 N at 600 r.p.m. for 20% of the time; and (c) Radial load of 2000 N at 300 r.p.m. for 55% of the time. The inner ring rotates and loads are steady. Select a bearing for an expected average life of 2500 hours.
A propeller shaft rotating at constant speed is subjected to variable loads.Ball bearing supporting the shaft are subject to variable radial loads as follows;16KN for 40 percent of the time,2KN for 10 percent of the time,4KN for 20percent of the time and no load for the remaining time of the cycle.The total life expected for bearing is 3×10^6 revolution at a liability of 94 percent.select the bearing by calculating; a)Net dynamic load for the bearing b)load rating of the bearing from the manufacturers catalogue
An 02-series ball bearing is to be selected to carry a radial load of 8 kN and a thrust load of4 kN. The desired life LD is to be 5000 h with an inner-ring rotation rate of 900 rev/min. Whatis the basic load rating that should be used in selecting a bearing for a reliability goal of 0.90?
b) Design a single row deep groove ball bearing with basic dynamic load rating of 33 KN to be used in a turbine to carry a radial load of 1584 N. The expected life of the bearing is 5591 hours at 529 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.8. The radial and axial load factors are 1.3 and 1.6 respectively and the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Axial load acting on the bearing in N
A single row deep groove ball bearing is operating at a speed of 2000rpm acted upon by a radial load of 10kn and thrust load of 8kn. The bearing is subjected to light shock load and outer ring is rotating. Determine the life rating of the bearing
A Self-aligning medium series bearing for bores of 85 mm is operating at 300 r.p.m for an average life of 9 years at 10 hours per day, is acted by a 15 kN radial load and 10 kN thrust load. The bearing is subjected to a light shock load and the inner ring is sationary. Determine the suitable self-aligning bearing. Mention the advantage of using self align bearing.
Select a doubler row deep groove ball bearing for a radial load of 5000 N and an axial load of 6000 N, operating at a speed of 1600 r.p.m. for an average life of 8 years at 20 hours per week. Assume W /C0 = 0.50
A single deep grove ball bearing series 3, the outer ring rotates at 1500 rpm with little shock load. Bearing has a bore diameter of 45 mm, working with a load 1890 lb radial and 1250 lb axial load. Determine the rated life and median life of the bearing. Use the design factors according to the attached table.
Estimate the life in hours of a 02-30 mm angular-contact ball bearing subjected to 20,000 revolutions per cycle. Each cycle consists of a radial load of 15 kN for 6 min, and then a change in load to 25.05 kN for 4 min. Determine the expected life of the bearing, in millions of revolutions, for each load, assuming the bearing has a C10 value of 20.3 kN. The expected life of the bearing for 15 kN load is ___ × 106 revolutions. The expected life of the bearing for 25.05 kN load is ____× 106 revolutions.