The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial distributed loading alongits length of w = 6 kN/m. Two concentrated loads also act on the rod: P = 6 kN and Q=4kN. Determine the normal stress in the rod at x = 0.8 m. Assume a = 0.4m and b=0.9 m. x a Answer: σ= i B b MPa Q

The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial distributed loading alongits length of w = 6 kN/m. Two concentrated loads also act on the rod: P = 6 kN and Q=4kN. Determine the normal stress in the rod at x = 0.8 m. Assume a = 0.4m and b=0.9 m. x a Answer: σ= i B b MPa Q

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter16: Lateral Earth Pressure

Section: Chapter Questions

Problem 16.3P: The soil profile at a site is shown Figure P16.3. Find the total horizontal normal stresses at A and...

See similar textbooks

Similar questions

The solid circular shaft is subjected to an internal torque of T= 6.0 kN.m. Determine the shear stress developed at point A and B
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
A hollow shaft with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P = 76 kN and torques TB = 15 kN-m and TC = 4 kN-m, which act in the directions shown. Determine the normal stress x at point H.
QUESTION 2) A bending moment of M=4 kNm, tan alpha (α)=0.577, acts on the section in the figure. Unbiased Determine the position of the axis and draw the stress distribution in the section
Determine the average normal stress at section a-a and the average shear stress at section b-b in member AB. The cross-sectional is square, 0.55 in. On each side.
NO. 4. The 150-kg bucket is suspended from end E of the frame. Determine the average normal stress in the 6- mm diameter wire CF and the 15-mm diameter short strut BD IN Figure 4.
A. Determine the maximum bearing stress in MPa if P = 115 kN. B. Determine the maximum shear stress in MPa if P = 115kN. C. Determine the maximum tensile stress in MPa if P = 11 kN.
The bar has a 140 mm by 20 mm rectangular cross section. If P = 190 kN, determine the force components perpendicular (N) and parallel (V) to a-a, the inclined surface area, and the normal and shear stress magnitudes acting on surface a-a.
If d = 450 mm, determine the absolute maximum bending stress in the overhang beam.
Determine the magnitude of the maximum vertical force P (in kN) that can be applied to the bell crank so that the average normal stress developed in the 10-mm diameter rod CD, and the average shear stress developed in the 6-mm diameter double sheared pin B not exceed 175 MPa and 75 MPa, respectively
The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius of 2.75 in. and an outer radius of 3.00 in. If the face of the sign is subjected to a uniform wind pressure of p = 150 lb>ft2, determine the state of stress at points C and D. Show the results on a differential volume element located at each of these points. Neglect the thickness of the sign, and assume that it is supported along the outside edge of the pipe.
knowing that P = 18 Kips, determine the maximum stress when r = 0.45 in and r = 0.70 in