The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain automobile distributors. For the configuration shown, where the wrench lies in a vertical plane and a horizontal 290-N force F is applied at A perpendicular to the handle, calculate the moment Mo applied to the bolt at O. For what value of the distance d would the z-component of Mo be zero? Assume a = 80 mm, d = 115 mm, h = 170 mm, 0 = 26° F Answers Moi d= i 0 d h -y i+ i mm j+ i k) N-m

The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain automobile distributors. For the configuration shown, where the wrench lies in a vertical plane and a horizontal 290-N force F is applied at A perpendicular to the handle, calculate the moment Mo applied to the bolt at O. For what value of the distance d would the z-component of Mo be zero? Assume a = 80 mm, d = 115 mm, h = 170 mm, 0 = 26° F Answers Moi d= i 0 d h -y i+ i mm j+ i k) N-m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.97P: The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces...

See similar textbooks

Similar questions

Find the internal force system acting on section 3 for the pin-connected frame.
The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
The 1800lbin. couple is applied to member DEF of the pin-connected frame. Find the internal force systems acting on sections 1 and 2.
In the assembly shown, member AB is rigidly attached to the wall while an L bar is pinned to AB at E. Two forces P and Q are acting on the assembly shown. Force P lies on the x-axis while force Q is applied at point D along a plane parallel to the yz-plane . Which of the following best approximates the magnitude of the moment of force Q about the y-axis?
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 16i - 13j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. Determine the magnitude of the moment of P about the y-axis in Nm. Determine the magnitude of the moment of P about the z-axis in Nm. Determine the magnitude of the moment of P about the origin (point O) in Nm.
In the assembly shown, member AB is rigidly attached to the wall while an L bar is pinned to AB at E. Two forces P and Q are acting on the assembly as shown. Force P lies on the x-axis while force Q is applied at point D along a plane parallel to the yz plane. 1. Which of the following quantities is/are zero? (Choices: A. Moment of P about the x-axis ; B. Moment of P about the y-axis ; C. Moment of P about the z-axis) 2. Which of the following best approximates the moment of force Q about point A? 3. Which of the following best approximates the equivalent force-couple set at point A of the applied forces P and Q? Note: F is the resultant force and Cis the resultant couple4. Considering the force diagram of member DE, which gives the complete set of reactions for the support at E? (Note difference of Force and couple reactions)
Static problem Determine the forces and internal moment at points 1 and 3 indicated in the figure. Consider the pins at A, B, and C. Points 1 and 2 are located just above and below pin C.
2) The ABO vertical arm, whose weight of mass m is neglected in the figure, is kept in balance with a spherical joint to the wall with 3 cables. Calculate the reaction forces at point O and the force on all ropes. m=610 Please write the answer on a piece of paper
Please reply as soon as possible, static problem Determine the forces and internal moment at points 1 and 3 indicated in the figure. Consider the pins at A, B, and C. Points 1 and 2 are located just above and below pin C.
Determine the moment MAB produced by the force F shown in the figure which tends to rotate the bar about the axis AB.
The assembly shown is supported by pin supports at A and B, and consists of four members connected by pins at C, F, and D. Find the reaction forces and/or moments at points C, D, and F to support the 30 lb. and 40 lb. forces shown below.
PROBLEM 3: A right-angled rigid pipe is fixed to a wall at A and is additionally supported through the cable CD as shown in the figure. The tension in the cable is 3 kN. Neglect the weight of the pipe. Use the Right-Hand-Rule to indicate the direction of the moment. [8] Calculate total force reaction at A. (ANSWER: 3.00 KN) [9] Calculate the moment reaction (including correct sign) at A about z-axis. (ANSWER: 2.168 KN-m) [10] Calculate the moment reaction (including correct sign) at A about x-axis. (ANSWER: -0.843 KN-m)