FQ3: Water (p=990 kg/m³ & μ= 0.0013 Pa.s) is pumping from an atmospheric water tank to water injection wellwith carbon steel pipe has same level, where the discharge pipe diameter is 12 inch, pipe length is 4700 m, piperoughness is 0.045 mm, and water flow rate is 0.065 m³/sec.1- Calculate discharge head, if the pressure at water injection well is 190 bar.2- Calculate pump liquid power, if pump section head value is 3.8 m.

Q3: Water (p= 990 kg/m³ & μ= 0.0013 Pa.s) is pumping from an atmospheric water tank to wa with carbon steel pipe has same level, where the discharge pipe diameter is 12 inch, pipe length is 4700 m, p roughness is 0.045 mm, and water flow rate is 0.065 m³/sec. 1- Calculate discharge head, if the pressure at water injection well is 190 bar. 2- Calculate pump liquid power, if pump section head value is 3.8 m. her

Q3: Water (p= 990 kg/m³ & μ= 0.0013 Pa.s) is pumping from an atmospheric water tank to wa with carbon steel pipe has same level, where the discharge pipe diameter is 12 inch, pipe length is 4700 m, p roughness is 0.045 mm, and water flow rate is 0.065 m³/sec. 1- Calculate discharge head, if the pressure at water injection well is 190 bar. 2- Calculate pump liquid power, if pump section head value is 3.8 m. her

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a cast-iron piping system of 450 ft length shown below, the rate of flow is 1 cfs at 70°F. Assuming the total head losses for the flow in the system is 10 ft, what is the energy head supplied by the pump E? a. 40 ft b. 50 ft c. 60 ft d. 510 ft e. None of the above
A pumping system has the following characteristics, f=0.015 length of thepipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipeis cast iron, and the system curve is:Hp= 34+ 5.47Q2Knowing that the system curve and the pump curve intersect at 12 cfsa. Determine Operation headb. Determine dischargec. Plot the system curve
Water at 16,2°C is to be discharged from a reservoir at a rate of 16,2 L/s using two horizontal cast iron (roughness value ɛ=0.00026m) pipes connected in series and a pump between them. The first pipe is 26,2 m long and has a 66,2 mm diameter, while the second pipe is 36,2 m long and has a 46,2 mm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged (KL=0.562), and losses associated with the connection of the pump are negligible. Neglecting the effect of the kinetic energy correction factor, determine the required pumping head, the minimum pumping power and electric motor power for total efficiency value of 76,2% to maintain the indicated flow rate. Water density is r=996,2 kg/m3, dynamic viscosity µ= 1.162x10-3kg/ms. Solve the problem by making the necessary assumptions and drawing the schematic figure.
Suppose the pump of Fig. P14–23 is operating atfree delivery conditions. The pipe, both upstream and downstreamof the pump, has an inner diameter of 2.0 cm andnearly zero roughness. The minor loss coefficient associatedwith the sharp inlet is 0.50, each valve has a minor loss coefficientof 2.4, and each of the three elbows has a minor losscoefficient of 0.90. The contraction at the exit reduces thediameter by a factor of 0.60 (60% of the pipe diameter), andthe minor loss coefficient of the contraction is 0.15. Note thatthis minor loss coefficient is based on the average exit velocity,not the average velocity through the pipe itself. The total length of pipe is 6.7 m, and the elevation difference is (z1 - z2)= 4.6 m. Estimate the volume flow rate through this pipingsystem. Complete Answer, Thank you
A2: FLUID FLOW, FLOW RATE & PRESSURE DROPProblem:4. Determine the average velocity in m/s for water flow in a 2 in diameter pipe, Schedule 40 chlorinated polyvinyl chloride (CPVC) pipe (2.375 in outside diameter and 2.047 in inside diameter) carrying cold water at a volumetric flow rate of 40 gpm.
This is a fluid machine question. Water reservoir is pumped over a hill through a pipe 450 mm in diameter and a pressure of 98.08 kPa is maintained in the summit water discharge is 30 m above the reservoir. The quantity pumped is 0.50 m3/s. rrictional losses in the discharge and suction pipe of the pump is equivalent to 1.5 m head loss. The speed of the pump is 800 rpm, what amount of energy must be furnished by the pump in kW?
Provide solutions A penstock with a diameter of 4 ft and length of 225 ft carries water (γ = 62.4 lbf/ft3) through a 200 ft drop from a reservoir to a turbine. The penstock entrance is 10 ft below the water surface. The ﬂow rate through the system is 500 cfs and water exits the turbine in a free jet with a velocity of 9 ft/s. The Darcy-Weisbach friction factor for the penstock is 0.01. Flow is turbulent and head losses at the entrances and exits of the penstock and turbine are negligible. (a) Draw the hydraulic grade line and energy grade line. Label transitions points with the height change using symbols (e.g. hL for pipe head loss) (b) Determine the head delivered to the turbine by the water in ft.(c) If the turbine and generator have a combined eﬃciency of 80%, determine the power in hp generated by the system.
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m.The total length and diameter of the suction and discharge pipes are 500 mm, 1500 m and 30 mm, 1000 m respectively. Assume a head lose of 2 meters per 100 m length of the suction pipe and 3 m per 100 m length of the discharge pipe. What is the required horsepower of the pump? **provide complete solution using bernoullis equation..provide illustration with labels like datum line and such** Show all formula derivation
A tanker carrying tolueneis unloaded to an onshore storage tank using the ship’s pumps. The pipeline is 225-mm inside diameter and 900-m long (200-m long suction line, 700-m long discharged line). Miscellaneous losses due to fittings, valves, etc., amount to 100 equivalent pipe diameters at the suction side, and 500 equivalent pipe diameters at the discharged side. The maximum liquid level in the destination storage tank is 30 m above the lowest liquid level in the ship’s tanks. The ship’s tanks are nitrogen blanketed and maintained at an absolute pressure of 1.05 bar (1 bar = 10^5 Pa). The storage tank has a floating roof, which exerts an absolute pressure of 1.1 bar on the liquid. The ship must unload 1000 metric tons within 5 hours. Taking pump efficiency as 70%, (ρ = 874 kg/m3, μ = 0.62 cP, Pvapor = 0.037 atm absolute). Determine: D. Discharge head (m) and pressure (Pa) E. Actual pump power (kW) F. Available NPSH (m)
A tanker carrying tolueneis unloaded to an onshore storage tank using the ship’s pumps. The pipeline is 225-mm inside diameter and 900-m long (200-m long suction line, 700-m long discharged line). Miscellaneous losses due to fittings, valves, etc., amount to 100 equivalent pipe diameters at the suction side, and 500 equivalent pipe diameters at the discharged side. The maximum liquid level in the destination storage tank is 30 m above the lowest liquid level in the ship’s tanks. The ship’s tanks are nitrogen blanketed and maintained at an absolute pressure of 1.05 bar (1 bar = 105 Pa). The storage tank has a floating roof, which exerts an absolute pressure of 1.1 bar on the liquid. The ship must unload 1000 metric tons within 5 hours. Taking pump efficiency as 70%, (ρ = 874 kg/m3, μ = 0.62 cP, Pvapor = 0.037 atm absolute). Determine: A. Pump head (m) B. Pump differential pressure (Pa) C. Suction head (m) and pressure (Pa) D. Discharge head (m) and pressure (Pa) E. Actual pump power…
A tanker carrying tolueneis unloaded to an onshore storage tank using the ship’s pumps. The pipeline is 225-mm inside diameter and 900-m long (200-m long suction line, 700-m long discharged line). Miscellaneous losses due to fittings, valves, etc., amount to 100 equivalent pipe diameters at the suction side, and 500 equivalent pipe diameters at the discharged side. The maximum liquid level in the destination storage tank is 30 m above the lowest liquid level in the ship’s tanks. The ship’s tanks are nitrogen blanketed and maintained at an absolute pressure of 1.05 bar (1 bar = 10^5 Pa). The storage tank has a floating roof, which exerts an absolute pressure of 1.1 bar on the liquid. The ship must unload 1000 metric tons within 5 hours. Taking pump efficiency as 70%, (ρ = 874 kg/m3, μ = 0.62 cP, Pvapor = 0.037 atm absolute). Determine: Discharge head (m) and pressure (Pa) Actual pump power (kW) Available NPSH (m)
9.7. Through a hydraulic turbine flow 2.8 m3/s of water. On the 1 m inlet pipe at elevation 43.5,a pressure gage reads 345 kPa. On the 1.5 m discharge pipe at elevation 39, a vacuum gage reads150 mm of mercury. If the total head lost through pipes and turbines between elevations 43.5and 39 is 9 m, what power may be expected from the machine?