Answered: The speed-density relationship for a…

The speed-density relationship for a particular road was found to be : u = 42.76 -0.22 k, Where u is the speed in km and k is the density in vehicles per km. capacity of the road will be-

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter3: Characteristics Of The Driver, The Pedestrian, The Bicyclist, The Vehicle, and The Road

Section: Chapter Questions

Problem 10P

See similar textbooks

Related questions

Q: Find the reactions at pins A, B, C, and D as well as roller E. Members ABC and CDE are continuous…

A: Calculation of reactions at pin A,B,C,D, as well as at roller E of given structure

Q: The brass bar AB and aluminum bar BC are joined at the collar B and fixed at their ends A and C. For…

A: A composite beam with a brass section and an aluminum section is given.Modulus of elasticityThermal…

Q: Q- To obtain the lake evaporation in cm, the evaporation observed from an ISI pan under similar…

Q: what is the bolt shear capacity of the shear connection in kips?

A: A 325 boltsBolt diameter d = 3/4 inNumber of bolt in shear connection n = 16 (top and bottom…

Q: 3. The clear spacing of the main longitudinal A. 140.6 B. 155.3 C. 165.7 forcements in m D.207.6

A: Diameter of column (D) = 450 mm Factored axial load (Pu) = 3170 KN Clear bar covering (d') = 40 mm…

Q: Determine the smallest cross-sectional area A for the members of the truss shown, so that the…

A: TO find the areas of each member of the truss if the vertical deflection at the point B is 10 mm.

Q: SAMPLE PROBLEM Cords are loop around a small spacer separating two cylinders each weighing 1056.54…

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A single-stage, trickling-filter plant consists of a primary clarifier, a trickling filter 70 ft in…

Q: mum bending moment that can occur at a section 7 m from

Q: IZADA 2 m 15 kN 20 kN m Im 10 kN/m 111 2 m B

Q: 6 m 4 m 30 N/m as shown below. Determine the following: 80 N 6 m 2 m www. 50 N 100 N The Reaction at…

Q: The figure as shown below is a rigid bar (ABCD) which was supported thru pin at B. Two bars was also…

A: A rigid bar ABCD as shown-P=78 kNTo Find-The value of diameter at pin B.

Q: Calculate hydraulic retention time (in days) for a complete mixed flow aeration tank for 87% BOD…

Q: Problem 2. A jet plane which weight 29430 N and has a wing area of 20 m² flies at a velocity of 250…

Q: 4) Draw the influence lines for (a) the moment at C, (b) the vertical reaction at A and (c) the…

Q: 100 k 40 k/ft ad 3 ft 2 ft 30 k/ft 1+6ft

Q: A pumping station at sea level is to supply 18000 m3/hour to the located at an altitude of 1694 m…

Q: During a particular stage of the growth of a crop, the consumptive use of water is 2.8 mm/day. The…

A: Given :-Consumptive use, Cu = 2.8 mm/dayDepth of available water, d = 80 mmAmount of water available…

Q: P11.21. Analyze the beam in Figure P11.21 by the moment distribution method. Determine all reactions…

A: To analyze the given beam using stiffness matrix method

Q: Using the method of virtual work, find the vertical displacment of Point D. E = Ksi 1 inz 29,000…

A: To find the vertical displacement at the point D in the given truss using the method of Virtual…

Q: A launching apron is to be designed at downstream of a weir for discharge intensity of 6.5 m³/s/m.…

A: A launching apron-Discharge per unit width silt factor f=1,Tail water depth d = 4.4 m,To Find-The…

Q: A parcel of land has been surveyed in the field and the lengths and bearings of the various sides…

A: Convert the reduced bearing to a whole circle bearing:LineDistance, mWhole circle…

Q: How many different types of buildings can one find in different places?

A: To mention the different types of buildings found in different places.

Q: 1. A simply supported rectangular timber beam with a span of 5.0 m is carrying UDL of 10kN/m (design…

A: Span of simply supported beam = 5mUniform distributed load = 10kN/mBending stress = 8 N/mm2

Q: Consider the area shown in graph. Suppose that a=4 m, b=6 m, and k=3/8 m^-1. Locate the centroid y…

A: a=4 m, b=6 m, To find:The centroid y of the shaded area.

Q: Problem 10.7 The shaded area shown in (Eigure 1) is bounded by a, y axes and the curve y²-2.89-0.52…

A: Given equation ;can be written as ;Now ;Substituting value of x we get ;

Q: for the constant hea permeability test set-u shown in the following figure, the followin…

A: L =30 mArea if specimen = 175 sq. cm.Constant head difference = 50 cmVolume of water collected in 5…

Q: 20 kN 3 m 7m 10 kN/m 8 m

Q: P.12.11 handwritten only

A: We have to find out the ILD of the given cases in figure no 12.11

Q: lessons / Various / ENGINEERING FACULTY / Civil Engineering / INS210_Fluid Mechanics 1 / July 3 -…

A: Note:-As, per guidelines we are only supposed to answer first three sub parts repost the remaining…

Q: For the distributed load below, what is the resultant force, FR (in N)? 1400 N/m TATT 15 m 8 m 77 Do…

A: Given:Required:Resultant force FR in N

Q: In a constant head permeability test, if the discharge coming out of the sample is 0.35 cm³/s find…

A: Discharge Q=0.35 cm3/sLength L=30 cm,Area A=250 cm2Head loss per unit length i = 0.25Coefficient of…

Q: solve for reaction at hinge a. 0 b. 4.275 C. 4.725 solve for reaction at roller a. 4.725 b.0 c.…

Q: 3 The average annual precipitation on a catchment of 350 km² is 200 mm and the runoff coefficient is…

Q: Why is the triangle method called the head – to – tail (or tip – to – tail) method

A: In civil engineering, vectors often represent forces acting on a structure or the components of a…

Q: For the following diagram, compute the rate of return on the $3810 investment. 3810 500 250 500 250…

A: A rate of return (RoR) is an investment's net gain or loss over a given time span, it is calculated…

Q: draw the shear and moment diagrams for the beam.

A: To draw the shear and moment diagramsPoints in the beam can be named as below

Q: A cup anemometer consists of two hemispherical cups of 12 cm diameter mounted in opposite directions…

Q: A500-ft curve, grades of g +2.50% and 2 50% VPI at station 96 80 and elevation 839 26 ft, stakeout…

A: Length of curve, Grade 1, Grade 2, VPI station, Elevation of VPI, To find: The elevation of full…

Q: Item 7-9 (Virtual Work Method) 7. The flexural rigidity of the frame shown is constant. Find the…

A: The frame is a structure in which the different type of indeterminacy is there. Which can be…

Q: A rectangular beam 400 mm deep and 300 mm wide is simply supported over a span of 4 m. the bending…

A: Width of beam (B) = 300 mm Depth of beam (D) = 400 mm Length of the beam (L) = 4m Allowable bending…

Q: A cantilever beam supports the loads shown. The cross-sectional dimensions of the shape are also…

A: Given:Required:Moment of inertia about centroidal z axisMaximum value of first moment of…

Q: How are passengers and their belongings safeguarded during vehicle transfers?

A: To explain the how the passengers and their belongings are safeguarded during vehicle transfers.

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: To find:a) The stresses and the magnitude of Txy and show them on a stress element.b) The principal…

Q: Materials for the ADT construction project? Respond.

A: ADT is an acronym for Aggregate Base Course (ABC), Dense Graded Aggregate (DGA), and Asphalt Treated…

Q: Design grit chamber to treat peak design flow of 150 MLD (3 x Average waste water flow of 50 MLD) of…

Q: PROBLEM 7: Two tangents converge at an angle of 40. The direction of the second tangent is due east.…

A: Tangents converge at angle=40 degreesThe bearing of common tangent= S40OECentral angle of the first…

Q: The ratio of reaction RA and Rg of the simply supported beam in the given figure is 5t 3t A 2 t/m 2m…

A: Apply equilibrium condition to determine support reaction :Sign convention :Clockwise moment is…

Q: A composite beam cross section is made up of two rectangular strips. Each of (100x50) mm placed and…

A: A composite beam cross-section-To Find-The axial stress in the steel portion.

Q: A Jet of oil of relative density 0.8 and of area 0.01 m² strikes normally on a stationary plate at a…

A: Relative density RD=0.8Area A=0.01 m2velocity v=20 m/sTo Find-The value of the force exerted on the…

Concept explainers

Intersection Design

An intersection is a location where two or more roads or railways meet or join. The traffic movement is controlled at the intersection that depends on its design and type. It governs the operation, efficiency, speed, capacity, and safety of the highways, airways, and railways. The movement of the pedestrian causes hazards and delays at the intersection.

Question

The speed-density relationship for a
particular road was found to be : u =
42.76 0.22 k, Where u is the speed
in km and k is the density in vehicles
per km. capacity of the road will be-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given that

VIEW

Step 2: Calculate the capacity of road

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

On a road, the speed - density relationship of a traffic stream is given by u = 70 - 0.7 k (where speed, u, is in km/h and density, k, is in veh/km). At the capacity condition, the average time headway will be
2. A highway is having a design speed of 65 km/h and its pavement is having a friction coefficient of 0.4. If the reaction time of drivers is taken as 2.5 sec and average length of vehicles as 5 m, determine the capacity of the highway.
The spacing of the cars moving along the same lane of an expressway is 40 m center to center. If the average velocity of the car is 60 kph, determine the volume of traffic in veh/hr.
Three cars travel over a 60 m. section of highway at constant speeds of 19, 20 and 25 m/s. Compute the time mean speed for this condition in m/s (two decimal places).
The cars travel over a 60m section of highway at constant speeds of 19, 20,and 25 m/s. a. Compute the time mean speed.b. Compute the space mean speed.
the average spacing of vehicles in a single highway is 50m center to center. The average speed of the cars us 30 kph. determine the volume if traffic in vehicles per hour.
The average center to center spacing of vehicles in a simple lane highway is 50 m. The volume of traffic is 600 vehicles per hour. Determine the average speed of the cars using this lane.. help
Calculate the setback distance on a national highway having horizontal curve of radius 300 m and length of 180 m. Assume speed of 80 km/h and coefficient of friction of 0.35 and perception-reactions time of 2.5 seconds.
The rate flow at a point in the highway is 1200 vehicles/hour. Find the space mean speed in mph if the density of traffic is 25 vehicles per mile
The free speed of a passenger car on a 4lane road is 90 km/hr, while that of a truckis 45 km/hr. Under the jam condition, theaverage length occupied by the passengercar is 5 m, while that of a truck is 10 m, thePCU of the truck is -
A 4921.26 ft portion of a highway is known to have a free-flow speed of 27.78 m/s and a capacity of 4500 vehicles per hour. If in a given hour, 3855 vehicles were countered at a specified point along the highway, compute the space mean speed and the density in veh/km. Use Speed-Density Model.
Consider a truck with a maximum power of 500 kW and a frontal area of 11 m2 . The maximum speed the truck can maintain on an incline with a grade of 2.5% is 15 m/s. Assume air density ρ = 1.225 kg/m3 and the “drag coefficient” is CD = 0.75. What is the mass of the truck?